Treo Pro CDMA HardSPL

[pinpoint30]

I am having a disconnect issue as well. When I run the Panther_CDMA_HSPL file, the Sprint CDMA Treo Pro shows the 3 colors (pant 200) screen and the computer shows the update utility. It says it is reading phone info, then comes back with a Update 202 error. During the reading phone info stage, Active Sync (with good connection) shuts down. I tried the manual panther file loaded on sd card in phone (with usb connected), then run the custom ruu file and get the same result. I installed the enablerapinew.cab file (per thread) and then tried both methods again with no luck. I do not have any phone locks enabled on my device. Any help you can provide is much appreciated.

[ooxteme]

i had luck disconnecting and reconnecting the usb on the second screen before the unlocker started. run hardspl first check box then say continue then when the next check box comes up click it unplug and replug usb then continue through the rest of the screens

almost forgot i did NOT install any of the cabs

[juttonn]

Originally Posted by DssTrainer

So if I do a hard reset on my phone, it resets the HSPL too ? I don't remember that happening on the HTC Touch.

Anyway, I'll have to do this step again I guess as it is showing 0.32 instead of 0.36 after i did a hard reset. I'm trying the SD method but that does nothing.

1. Download HSPL
2. Rename from ruu_unsigned.nbh to PANTIMG.NBH
3. Copied to my phone storage card (root)
4. Ran the Manual SSPL program (also in root)
5. I get tricolor screen.... and it just sits there
6. I read elsewhere that you need to press the power button at the tricolor screen but that didn't work either

I'm getting the same result. I bought the Treo Pro for my wife on ebay and it didn't come with a USB cable. The other thing I tried was going into the boot loader (hold down power and camera button and then pushing soft reset button). When I do that i briefly get the tri-color screen, then the screen goes gray and says "Loading..." But it hangs there forever (I left it there for 30 minutes or so).

I tried redownloading files, I made sure the SD card is fat32, etc. Anyone have any other ideas? Thanks

[skeegcpp]

Originally Posted by juttonn

tried redownloading files, I made sure the SD card is fat32, etc. Anyone have any other ideas? Thanks

make sure the PANTIMG.nbh is on the root and that there isn't any other files like it on the root...cuz it sounds like its trying to update 2 files or sumthin
now when unlocking via sd card, at the end it mite jus say loading on the screen or give u a rom update error..ignore it, soft reset and cee what ya get

[frood]

Originally Posted by ooxteme

i had luck disconnecting and reconnecting the usb on the second screen before the unlocker started. run hardspl first check box then say continue then when the next check box comes up click it unplug and replug usb then continue through the rest of the screens

almost forgot i did NOT install any of the cabs

That worked for me too, thanks!

[ooxteme]

glad i could help!!!

[chstroup]

Originally Posted by Malachi

OK, thanks to Cmonex I got it fixed.

Here is what she told me:

"hi, just connect to mtty, and use: "set 16 0".
itwill be fine then "

I did it, and soft reset, and everything is fine.

Originally Posted by Malachi

yes, tried that too, but it won't connect to pc. bootloader screen shows USB, but activesync won't recognize it and RUUs wont' either.

Thanks for the effort though.

Originally Posted by Malachi

Bump. anybody?

Originally Posted by Malachi

Can anybody help me?

Long story short, I was flashing back to stock SPL, using sd card, and pulled the sd card out while it was flashing (don't ask, I seemed to forget for a moment what I was doing and realized I needed my card for my other phone Now, I have the stock SPL, shows PANT200 SPL-0.36.0000 CPLD-2 when phone starts, and says Upgrade ROM code error Please Try Again. But, if I put my sd card in it with PANTIMG.nbh SPL file, then I get a screen that says "Loading...". And that's it, left it like that forever it seems and no change.

Any idea? It won't connect to the computer so I can't flash from computer. Even QPST won't find it.

TIA,
Malachi

I am really stuck like the above quote's with the same situation. My phone is stuck in the 3 bar color bootloader which says
PANT200
SPL-0.36.0000
CPLD-2
Upgrade ROM code error, please try again.

I have attempted to load the rom using a blank, formatted sd card with the renamed PANTIMG file but that only takes me to a gray screen which shows loading but never goes any further. I have read through all the posts and see mtty.exe was the solution. I have tried using mtty.exe but not sure how to do it. i have the usb plugged into the phone and computer (which doesn't recognize it) and selected the USB port in mtty. It says the USB is closed. What can i do at this point to get out of this bootloader screen so i can flash a stock rom? Is the phone bricked??

Thanks in advance

[chstroup]

disregard, got an official sprint rom release to work!

[madvek]

Let me apologize up front here. First timer/newbie as far as phones go anyway.

I've been going through this step by step with no luck,reading tutorials and stickies but I must be missing something you guys are taking for granted.

I downloaded all the files, was able to connect and run the RUU but always boot back to 6.1.


“Extract to empty folder” Does that mean on the on PC or treo?

Do the RUU_signed.nbh and SSPL-Manual-PartnerCMA go in the same folder or elsewhere?

I follow steps in the RUU. When I get to step to verify updating from one ROM to new one, there is no choice to choose a different ROM.


"Take the file (RUU_signed.nbh) and put it in Cfay's custom RUU found here"

When I run the RUU, I don’t see an option to open a nbh file or “put in an RUU”
Thanks for any help!

[skeegcpp]

@madvek, this thread is for unlocking ur fone. which is required to then flash a custom rom. i use cmonex's unlocker. follow her instructions closely and all shud end well

Originally Posted by madvek

Thanks will do, sorry bout that.

Done! Success! thanks again.

no need to say sorry, u have to ask to know sometimes, right?