|ROM|¯`·.¸¸.- Energy -.¸¸.·´¯ * |July 4| 21916|29022 * Sense 2021 + flavors

[iknight8]

Originally Posted by tonyt4ever

LOL I think I have whatever is in this Thread...... Im still having issues. At the moment im not crying. I still Luv this Rom.

back up your files and install this CAB file and hope it works out for u!
keep me posted...

[Overproof]

Originally Posted by GaryMcQ

I have the Feb 26 CDMA version of 21892 Sense 2.5.2012 on my Verizon Touch Pro2, and the Feb 26 GSM version on my wife's AT&T Tilt2. On Both devices, after the phone has been idle for, say 30 minutes, and I press the top left button to light up the screen, the only thing that comes back are the top and bottom curtains. All information in the main window is blank. I am able to get it to display all information after touching the top icon bar, and then tapping on Done at the bottom. Is anyone else having this problem, and if so know of a solution? Other than that, the ROM runs flawlessly.

I've had this happen a few times.

[Dead_Cow]

I'm not sure where to post a serious problem I'm having with this ROM. Anyhow, here goes.

I have a Verizon TP2

I'm using (or rather TRYING to use) Energy.RHOD500.23541.Sense2.5_with_MaxManila.Feb.2 6.7z

Here's my symptom:

When Data and Activesync are enabled on the phone, I can no longer dial out. I get "The Network is Busy, Please Try Again Later".

If I do not enable activesync, I can use the data and place calls fine. Once I've enabled activesync, I cannot use the phone for outbound calls until I reflash the phone. No amount of turning off the data connection and rebooting, hard resetting, etc will allow me to make calls. I should say, that for a SHORT (like MAYBE 10 minutes) after I enable activesync, I can dial out and sync the phone.

I can receive calls fine. It's like the dialer cannot properly interrupt the data connection to make the call.

Maybe unrelated, but going to wireless controls > 3G >and trying to select a band results in the error "You have an ongoing voice call and the band cannot be changed now. Please try again later". I should note that in the "Network type" there is NOTHING selected (not even auto). I can force WCDMA and then back to auto by going into airplane mode. It does not resolve my dial-out problem.

So far, to try and resolve this, I've:

• Reflashed and reprovisioned.
• Hard reset and reprovisioned.
• Reinstalled the base ROM, reprovisioned, reinstalled Energy.RHOD500.23541.Sense2.5_with_MaxManila.Feb.2 6.7z and reprovisioned
• Reflashed, reprovisioned and tried the MRX_Verizon cab
• Asked the phone what it's problem is
• Cursed at the phone.

As you can see, I'm nearing wit's end.

If there's any input anyone can give me, I'd really appreciate it. I'd love to be able to call people AND use this ROM. I feel like I should create a new thread for this, but I don't know where would be best without it being ignored.

[glenwill]

Originally Posted by Dead_Cow

I'm not sure where to post a serious problem I'm having with this ROM. Anyhow, here goes.

I have a Verizon TP2

I'm using (or rather TRYING to use) Energy.RHOD500.23541.Sense2.5_with_MaxManila.Feb.2 6.7z

Here's my symptom:

When Data and Activesync are enabled on the phone, I can no longer dial out. I get "The Network is Busy, Please Try Again Later".

If I do not enable activesync, I can use the data and place calls fine. Once I've enabled activesync, I cannot use the phone for outbound calls until I reflash the phone. No amount of turning off the data connection and rebooting, hard resetting, etc will allow me to make calls. I should say, that for a SHORT (like MAYBE 10 minutes) after I enable activesync, I can dial out and sync the phone.

I can receive calls fine. It's like the dialer cannot properly interrupt the data connection to make the call.

Maybe unrelated, but going to wireless controls > 3G >and trying to select a band results in the error "You have an ongoing voice call and the band cannot be changed now. Please try again later". I should note that in the "Network type" there is NOTHING selected (not even auto). I can force WCDMA and then back to auto by going into airplane mode. It does not resolve my dial-out problem.

So far, to try and resolve this, I've:

• Reflashed and reprovisioned.
• Hard reset and reprovisioned.
• Reinstalled the base ROM, reprovisioned, reinstalled Energy.RHOD500.23541.Sense2.5_with_MaxManila.Feb.2 6.7z and reprovisioned
• Reflashed, reprovisioned and tried the MRX_Verizon cab
• Asked the phone what it's problem is
• Cursed at the phone.

As you can see, I'm nearing wit's end.

If there's any input anyone can give me, I'd really appreciate it. I'd love to be able to call people AND use this ROM. I feel like I should create a new thread for this, but I don't know where would be best without it being ignored.

You've posted in the right place. This is the thread for this ROM. However, I'm not aware of this being a problem others are having with this ROM. I'm certainly not.

When you reflashed the stock ROM, did you test to confirm you don't have the same problem? Maybe live with stock for a day and see if all works as expected.

A provisioning CAB should not be needed for base functionality. Have you tried flashing NRG, and test without anything else installed? I certainly don't need a provisioning CAB for Sprint. I don't think the Verizon users do either, but I don't have experience there.

[Dead_Cow]

Originally Posted by glenwill

You've posted in the right place. This is the thread for this ROM. However, I'm not aware of this being a problem others are having with this ROM. I'm certainly not.

I have to load a certificate which, when I sync to my corporate mail server enforces security on the device. Do you have to do that too? This problem ONLY has occurred to me with the NRG rom. Unfortunately, it's my favorite ROM to date.

Originally Posted by glenwill

When you reflashed the stock ROM, did you test to confirm you don't have the same problem? Maybe live with stock for a day and see if all works as expected.

I have lived with stock for a day, and it works. Reflashing back to NRG, I lived with that at stock for a day, too, then enabled AS. It's how I know if I enable activesync that my problem occurs. No activesync = no problems. Unfortunately, it also means "no mail", which would also translate to "no job".

Originally Posted by glenwill

A provisioning CAB should not be needed for base functionality. Have you tried flashing NRG, and test without anything else installed? I certainly don't need a provisioning CAB for Sprint. I don't think the Verizon users do either, but I don't have experience there.

I didn't think I needed a provisioning cab. I tried it out of desperation.

[kashabrown]

I use verizon also, and utilize a hosted exchange service for my email (which has security also). My process is to flash stock 6.5/hard reset/*228 programming/flash 23541 MM rom/hard reset-soft reset and am good to go.

[Dead_Cow]

Originally Posted by kashabrown

I use verizon also, and utilize a hosted exchange service for my email (which has security also). My process is to flash stock 6.5/hard reset/*228 programming/flash 23541 MM rom/hard reset-soft reset and am good to go.

I've done almost that.... but... why do you do that? Did you experience the same problem as me? See, everything else works, BUT this problem. (Which I'm temporarily working around using one dialer and Google Voice).

[shaolinsoldier79]

Wirelessly posted (Opera/9.80 (Windows Mobile; WCE; Opera Mobi/WMD-50369; U; en) Presto/2.4.13 Version/10.00)

I am on verizon, what is the provisioning thing all about I have never done that but seen it mentioned many times..???

[Dead_Cow]

Originally Posted by shaolinsoldier79

Wirelessly posted (Opera/9.80 (Windows Mobile; WCE; Opera Mobi/WMD-50369; U; en) Presto/2.4.13 Version/10.00)

I am on verizon, what is the provisioning thing all about I have never done that but seen it mentioned many times..???

Provisioning sets the phone to work with your network on your account. For Verizon, it's dialing *228 from the handset, then pressing one when the computer answers and waiting until it says "your phone has been programmed successfully", at which point it will hang up and soft reset the phone.

[shaolinsoldier79]

Wirelessly posted (Opera/9.80 (Windows Mobile; WCE; Opera Mobi/WMD-50369; U; en) Presto/2.4.13 Version/10.00)

Originally Posted by Dead_Cow

Provisioning sets the phone to work with your network on your account. For Verizon, it's dialing *228 from the handset, then pressing one when the computer answers and waiting until it says "your phone has been programmed successfully", at which point it will hang up and soft reset the phone.

ok so what are these proviisioning cabs I hear about?