nueLED - configure/customize your LEDs... - Page 13

**no2chem** · #1 (**permalink**) 02-24-2008, 10:46 PM

Quote:

Originally Posted by cj10488

RED LED

0400040005000000050000000000000000000000

address 4 mode 4

cool. I believe the 50000000500000000000 code means frequent refresh or something... ill have to figure it out...

actually, maybe 50000xxx causes the led to take higher priority or something. I know the system constantly sends address 4 mode 0, so this might be causing it to turn off...
... so disable address 4 mode 0... and it _should_ work...

yep, it worked.. signal light red now so far.... edit: it doesn't stay on power down... =/, thanks though cj10488!

cj10488 · #2 (**permalink**) 02-24-2008, 10:01 PM

I just went in and did Test and it causes it to blink forever

James

cj10488 · #3 (**permalink**) 02-24-2008, 10:04 PM

Actually after I setup my redirect for the service light to the Red light it does in fact blink a few times and then stops..

James

cj10488 · #4 (**permalink**) 02-24-2008, 10:15 PM

Well I did another reset and my Red SErvice light has been going since... this has been about 10mins..

1 thing I did notice is that the Orange Charge light does not light while the red light is blinking...

James

cj10488 · #5 (**permalink**) 02-24-2008, 11:50 PM

No problem... It wasnt too difficult... It is the least I can do...

James

qwho · #6 (**permalink**) 02-25-2008, 09:57 AM

I believe the orange light is the red and green lit at the same time. I've seen the combo red-green LEDs at radio shack, which are to display red, green, and orange. Check out the quote below...

Quote:

Originally Posted by cj10488

1 thing I did notice is that the Orange Charge light does not light while the red light is blinking...

James

That's probably because the command to keep the red blinking is interfering with the orange light command, which is to have the green and red on at the same time. Now what is interesting to me is that I originally thought the left LED could only display blue, but the poster who saw a white light come from it makes me think maybe it can display other colors.

**no2chem** · #7 (**permalink**) 02-25-2008, 07:32 PM

Quote:

Originally Posted by qwho

I believe the orange light is the red and green lit at the same time. I've seen the combo red-green LEDs at radio shack, which are to display red, green, and orange. Check out the quote below...

That's probably because the command to keep the red blinking is interfering with the orange light command, which is to have the green and red on at the same time. Now what is interesting to me is that I originally thought the left LED could only display blue, but the poster who saw a white light come from it makes me think maybe it can display other colors.

also, i've seen a white led on the left of the mogul before when i was messing with values...

...too bad i can't replicate it.. at the moment.

**no2chem** · #8 (**permalink**) 02-25-2008, 08:00 PM

ok, got another address ,

slow notification LED, address 4, mode 8
you'll need to turn off the address 4, 0 control in order for this to work...

**[sammich]** · #9 (**permalink**) 02-25-2008, 11:05 PM

Umm... can I get my phone to flash like a RAINBOW??

Just kidding, btw...

I still think there is a way to combine colors. What kind of LEDs are these lights? Are there multiple colors, or is it one that can change

unknown_g · #10 (**permalink**) 03-01-2008, 11:35 AM

Quote:

Originally Posted by no2chem

ok, got another address ,

slow notification LED, address 4, mode 8
you'll need to turn off the address 4, 0 control in order for this to work...

I'm using the Sprint Touch and the addr 4 mode 8 does 4 short amber then a very fast red then stops. I think it might be the addr 4,0 control that might be causing it to stop. How do you turn it off?

Also isn't the diag suppose to record whenever an led blinks? or am i misunderstanding how it works?

Also the addr 4 mode 4 does give me the red led but stops short after the addr 4 mode 0 keeps in.

Also I see that we can manually test for modes over 2; there a way that the Cycle LEDS can be made to go as high as mode 8 since we are seeing things happening at mode 8?