Free Tethering? I think so.

[Primenall]

There is no need to set it for PAM, just leave set to PCS.

It's so easy I don't understand why anyone has a problem, just make sure activesync is installed as it also installs the modem drivers.

1. Change registry entry for rilphone.dll
2. Plug usb in computer only
3. Open Internet sharing, leave settings usb and PCS then hit connect
4. Plug usb into 6800, wait a few seconds for it to set up connection on computer, you can now close IE now as well.

That's it, remember when your done hit disconnect on your 6800 FIRST no matter what.

[Darkness231]

Originally Posted by Primenall

There is no need to set it for PAM, just leave set to PCS.

It's so easy I don't understand why anyone has a problem, just make sure activesync is installed as it also installs the modem drivers.

1. Change registry entry for multi-nai
2. Plug usb in computer only
3. Open IE on 6800
4. Open Internet sharing, leave settings usb and PCS then hit connect
5. Plug usb into 6800, wait a few seconds for it to set up connection on computer, you can now close IE now as well.

That's it, remember when your done hit disconnect on your 6800.

This is the procedure that works for me, with the exception that I have to hit connect when there is a active data transfer. If I do it while connected and not transferring data it disconnects and tries to reconnect then kicks the 67 error. This happens even after the wmodem regs are 0zd out

[getinked5]

Originally Posted by Primenall

There is no need to set it for PAM, just leave set to PCS.

It's so easy I don't understand why anyone has a problem, just make sure activesync is installed as it also installs the modem drivers.

1. Change registry entry for multi-nai
2. Plug usb in computer only
3. Open IE on 6800
4. Open Internet sharing, leave settings usb and PCS then hit connect
5. Plug usb into 6800, wait a few seconds for it to set up connection on computer, you can now close IE now as well.

That's it, remember when your done hit disconnect on your 6800.

yeah i think my phone was just defective...the whole internet didnt work then it worked now it doesnt work again....i should have my new phone tomorrow

[scottdw]

Originally Posted by getinked5

yeah i think my phone was just defective...the whole internet didnt work then it worked now it doesnt work again....i should have my new phone tomorrow

So there is no need to do the whole ##3282# step???

[getinked5]

Originally Posted by Primenall

There is no need to set it for PAM, just leave set to PCS.

It's so easy I don't understand why anyone has a problem, just make sure activesync is installed as it also installs the modem drivers.

1. Change registry entry for multi-nai
2. Plug usb in computer only
3. Open IE on 6800
4. Open Internet sharing, leave settings usb and PCS then hit connect
5. Plug usb into 6800, wait a few seconds for it to set up connection on computer, you can now close IE now as well.

That's it, remember when your done hit disconnect on your 6800.

i just followed these steps by Primenall...works perfect...my other phone i guess was malfunctioned piece of hardware. did a ROM swap hard reset everything...still didnt fix the 67 error code i was getting...just got a new phone monday and i'm tethering from it right now to test. works great Primenall.

[Primenall]

Yeah that's great, just remember to always hit "disconnect" before you unplug the cable or close Internet sharing as that can cause the 67 error if you don't.

[skimaniac6]

Originally Posted by Primenall

There is no need to set it for PAM, just leave set to PCS.

It's so easy I don't understand why anyone has a problem, just make sure activesync is installed as it also installs the modem drivers.

1. Change registry entry for multi-nai
2. Plug usb in computer only
3. Open IE on 6800
4. Open Internet sharing, leave settings usb and PCS then hit connect
5. Plug usb into 6800, wait a few seconds for it to set up connection on computer, you can now close IE now as well.

That's it, remember when your done hit disconnect on your 6800.

I did this and my phone says connected, but the web browser won't load a page, I normaly use a wireless network at home, disabled that but can't figure out how to connect to the network. Everything seems fine on the phone its the computer I'm having trouble with. Any help would be great.

[skimaniac6]

sorry, it seems all works fine now... Thanks for the tips and tricks as I cross my fingers and hope my bill doesn't go up....

[letsgoflyers81]

Do you use BT or USB for tethering? When I tried last weekend I was just using BT. So I'm not sure if it was the Vision connection or PAN that was dying.

[seromogulsprint]

Hello, I have a quick question. I am planning on buying the mogul while I am in Oregon (until tomorrow). I was wondering if I could thether this to my laptop without being charged? I currently have the sero plan and a samsung a900m that I disabled NAI on. Can I disable NAI or something on the Mogul and get online? Thanks