|
||||
Ack.... 1st freeze
Ack, had my 1st phone freeze today.
Which, I'm not sure, but may be due to hardware, as this phone (6700) was prone to freezing. Then again, never had a freeze with the latest release of WM5, 3.5 AKU. Will wait and see.... |
|
||||
Quote:
Well I guess all that preparation was worth it, I had not a single problem although I haven't played around very much yet. I did confirmed basic functionality of the phone (incoming and outgoing) , browser, EVDO, and orientation switching. I noticed a couple of people claiming that several "hard resets" cleared up a wide variety of problems, so I did six hard resets in a row figuring it might not help but it couldn't (or at least shouldn't) hurt either. Each time I interrupted the process before the "3 second" timeout. I did notice that every time I saw WM6 it caused me to giggle like a little girl. Although I do blame Helmi for these embarrassing outbursts, to be fair there probably is not a lot than can be done about it at this point in time. As a point of comparison my "Device Information" was: ROM version: 2.06.00 WWE ROM date: 02/22/06 Radio version: 1.27.00 Protocol version: SNAZ-40306 ExtROM version: 2.05.303 WWE PRI version: 1.19_003 Browser version MSIE 4.01 CPU: Intel(R) PXA2700 Speed: 416MHZ RAM size: 64 MB Flash size: 128 MB Flash chip type: M-Systems Model No.: PA10A1 Platform: PocketPC Data bus: 32 bits Storage size: 39.59 MB Here is my "Device Information" after flashing: ROM version: 3.50.00 WWE ROM date: 04/25/07 Radio Version: 1.27.00 Protocol version: SNAZ-40306 ExtROM version: <blank> Hardware version: 0041 PRL version: 20229 PRI version: 1.19_003 Browser version: MSIE 6.0 CPU: Intel(R) PXA270 Speed: 416 MHz RAM Size: 64MB Flash Size: 128 MB Flash chip type: M-Systems Data bus: 32 bits Storage size: 39.59 Model No.: PA10A1 Platform: PocketPC My new WM6.0 "System Information" shows: Windows Mobile 6.0 (WinCE 5.02) PA10A1 Program Memory - 40% 50.2MB/20.14MB Storage Memory - 8% 39.6MB/3.2MB Extended_ROM2 - 98% 9.9MB/9.77MB Storage Card - 6% 968.3MB/58.19MB I am not familiar with "Extended_ROM2" but I suspect this is where all the new stuff went. I also suspect that \Extended_ROM\ is still there although I normally access that with Total Commander/CE 2.0 (Pocket PC ARM/XSCALE) which I haven't installed yet. And when I set up "Weather" it listed me as "Lawrence, US" and I would have prefered "The Peoples Republic of Lawrence, KS" More later as I begin to resync with my laptop, text message, and amaze my fellow cow orkers. |
|
||||
First thanks for the release. I just got my 6700, it's not even on verizon yet, but I've upgrade. I am wondering if anyone has a WM6 Wi-fi Guide, mine keeps trying to dial out vs. connecting to a wi-fi network in my office.
Thanks, D~ |
|
||||
Thanks for the release Helmi. As soon as I get paid, I'm sending a nice donation towards your way. Unfortunately I have one problem. My contacts tab doesn't work at all except my SPB Contacts. Can someone help me with this problem. I re-downloaded a couple of times and same problem. Thanks.
|
|
||||
Killa,
I had the same problem. Lost all my contacts. Tried syncing without luck. Finally, did a hard reset, and set it back to "default". Contacts magically reappeared. Not sure why, but I'm not arguing. I also missed the transcriber which I used much more than the keyboard. I found that the Calligrapher software was even better. |
|
||||
hey guys, can anyone help me with loading mw6? i downloaded both verizon versions, put my phone in bootloader mode, and double clicked on both versions and hit run and nothing happens but an empty dos window pops up for a second and goes away. in boot loader mode it shows usb v1.02. any thoughts of what i'm doing wrong, or any steps i might be skipping?
|
|
||||
Quote:
|
|
||||
Data Connection Disabled
First and foremost this update ROCKS!!!!! I was hesitant at first because I have never used other-than-verizon firmware. I love my phone again!!!!
I did notice one thing. I tried doing a couple of searches but couldn't see anything so I hope this is not a repeat. When I go into Comm Manager the Microsoft Direct Push and Data Connection buttons are disabled. I can get the data connection OK when I send a MMS message, but that is the only way I have been able to get it to turn on. Any ideas? |
|
||||
Quote:
__________________
Check out Dropbox - vv
Click Here - Free 2GB file hosting |
|
|
|