Touch Pro CDMA Hard-SPL brought to you by CDMA Raphael Elite Team

[wildpig]

i got my TP activesynced. But whenever i runRaphael_CDMA_HSPL_037.exe, it would detect my device and the rom as 1.03.651.3 and say if i want to upgrade the rom to 0.37.spl. i ask it to proceed but after a while it just gives error 202 connection. Anyone can help me out? thanks

[bparent]

I have an Alltel Touch Pro and want to use on Verizon. Do I still use this guide and Raphael for Alltel and just use a Verizon rom when updating?

[wildpig]

I finally got my phone to work with activesync to install the hspl. Just in case if anyone else has problem with getting activesync to work correctly

Program = > Activesync = > Menu => Connection => Synchronize all PC using this connection and check USB

also

Settings => Connection => USB to PC => make sure to uncheck Enable advanced network function (even if Activesync on your pc does recognize the device)

If this has been mentioned, sorry for the redundancy

[pink_mist_rocks]

HELP... As with alot of people earlier i was putting my touch pro back to original due to USB is inop and wanted to turn it in. I have read thru this and the sister thread about flashing with SD. Here is steps i took...you hopefully will see that i have done all but one step correctly and think i scr#wed myself.

Put Stock Sprint .nbh on sd as RAPHIMG.nbh...used stylus to put in bootloader..all worked fine.

Then put the relocker .nbh (as RAPHIMG.nbh..and used stylus versus the Hard SPL exec file in main memory...arrrrrggghh It tried loading the new (locker .nbh) and now is sitting in loading..

Removed SD card and attempted soft reset realizing i messed up the previous step by not using the .exe file to get to bootloader.

Yes i got the ROM code error but where the spl used to say codex it now reads SPL-0.37.0000

Formatted card and tried again to put original step one Sprint .nbh as RAPHIMG.nbh and stays stuck in loading...

Any ideas?

[razorloves]

Originally Posted by pink_mist_rocks

HELP... As with alot of people earlier i was putting my touch pro back to original due to USB is inop and wanted to turn it in. I have read thru this and the sister thread about flashing with SD. Here is steps i took...you hopefully will see that i have done all but one step correctly and think i scr#wed myself.

Put Stock Sprint .nbh on sd as RAPHIMG.nbh...used stylus to put in bootloader..all worked fine.

Then put the relocker .nbh (as RAPHIMG.nbh..and used stylus versus the Hard SPL exec file in main memory...arrrrrggghh It tried loading the new (locker .nbh) and now is sitting in loading..

Removed SD card and attempted soft reset realizing i messed up the previous step by not using the .exe file to get to bootloader.

Yes i got the ROM code error but where the spl used to say codex it now reads SPL-0.37.0000

Formatted card and tried again to put original step one Sprint .nbh as RAPHIMG.nbh and stays stuck in loading...

Any ideas?

you have to extract the nbh from a shipped sprint rom. it must be the shipped rom because you are locked now. that is your problem. just use winrar to extract the shipped rom exe and you'll see the nbh file you need.

[pink_mist_rocks]

@razorloves.... thhhhhhaaaaannnnkkkkkk yyyyyyoooooouuuu. Wow.. i really thought i was seriously jacked...the recommendation worked...just fyi for anyone else who might of been as careless as myself...again. Read the directions several times...i have done this time and time again with other phones...just got careless.

[fubulg6000]

Forget about the help. Phone acted retarded and worked on the second shot.

Thanks!

I have looked and looked you guys are the best ,thanks again!

[jokergp]

Ok so i tried un lockingg my touch pro and i used the 0.25.MFG one to unlock the phone when it was done it reseted it self but as it started 2 load up it staued at a white screen and displays red numbres with letters in the front what can i do to get out of this???

[bparent]

I have an Alltell TP , but want to use on Verizon. Will this work? Which version to use?