[CAB] GSM&CDMA Project Android Port and Startup Utility [01/23] FRX04 Reference! - Page 88

**flyers2114** · #**871** (**permalink**) 07-30-2010, 11:05 PM

Quote:

Originally Posted by khalidabuu

how do i get the market to work in this build ?

Is your internet working.....as long as it is than market will work....

Quote:

Originally Posted by colombia81er

My phone aint charging in driod but once i go into WM it will

.

something is going on funky for you.....mine is charging fine...

khalidabuu · #**872** (**permalink**) 07-30-2010, 11:22 PM

yea my inet is working but every time i click market a white screen opens and closes

**flyers2114** · #**873** (**permalink**) 07-30-2010, 11:28 PM

Quote:

Originally Posted by khalidabuu

yea my inet is working but every time i click market a white screen opens and closes

hmmmmmmm............not sure then I have not seen that....

**PropagandaX** · #**874** (**permalink**) 07-31-2010, 01:11 AM

market working fine for me. This build is nice but the touchscreen response is a little slow

khalidabuu · #**875** (**permalink**) 07-31-2010, 04:29 AM

did u do anything special before or after you installed the cab ?

sykosoft · #**876** (**permalink**) 07-31-2010, 06:04 AM

Quote:

Originally Posted by captobie

I was going to say, "of course everyone knows, it's in the FAQ." But I went back and looked and it's no longer there.

What it said was the you needed to have the SIM card out for the first boot, but this trick would work afterward.

Anyway, I've found that leaving the SIM card in with the phone set to CDMA only the phone won't connect to any network when booting into Android about 30% of the time. Then I have to reboot back into WinMo and reload Android... it's much easier just to leave the card out.

I've yet to have this issue (and I delete or rename andboot every time a new build comes out, so fresh boot every time). I haven't taken my sim card out since that discovery, and it works without fail, every time.

Michael

domoarigato · #**877** (**permalink**) 07-31-2010, 08:52 AM

ok... ive just installed the reference version and it doesnt seem to be as animated as blazn? ie. when i hit the app button it just switches, it doesnt do the zoom thingy. is this normal?

the only reason i installed reference is be cause blazn seems to corrupt itself over a while, am i the only one experiencing this?

nitefall · #**878** (**permalink**) 07-31-2010, 04:39 PM

I have searched but there is just to many results that have nothing to do with what i am looking for.
I'm having problems with the market place showing paid apps. I tried to use market enabler with the recommended settings for sprint that i found somewhere on here and it just made it so marketplace wouldn't connect at all.

If anyone can point me in the right direction or tell me if it isnt working at all I would appreciate it.

Running the newest blzn with the zimg that was posted to increase the incall volume

Thank you

Overmann · #**879** (**permalink**) 07-31-2010, 04:45 PM

BLAZN overclocks your Clock Speed to 700 MHz. It's always possible your phone's hardware isn't of good enough quality to run at that speed.

Remember, these phones were tested to run 528 MHz, and potentially they can run faster, but are not tested if they can run faster. Flaws in the electronics might prevent that.

colombia81er · #**880** (**permalink**) 07-31-2010, 10:02 PM

Quote:

Originally Posted by flyers2114

something is going on funky for you.....mine is charging fine...

Lol well it won't charge, then GPS signal will just relocate to Lat.0 Lon. 0

Lets see on the new updates if it will work that.