Transfer Caller Announcement to BT headset

[rlith]

Originally Posted by rddt

Sorry - Treo 700wx with included wired headset's button, for starters. I'd love to obtain a different wired or BT headset if I can get the headset button to work for initiating voice commands.

Samsung WEP200 works beautifully with MSVC 1.6, loud as well (Do not buy from ebay, will most likely be counterfit)

[colonel]

Originally Posted by rddt

Sorry - Treo 700wx with included wired headset's button, for starters. I'd love to obtain a different wired or BT headset if I can get the headset button to work for initiating voice commands.

Don't even know about the wired headset. Try pressing and holding maybe To truely take advantage of VC you should really look into getting a BT headset.

[rddt]

Is the Samsung WEP200 the only one of only a few that are compatible with the Treo 700wx? I've heard many complaints re: BT + Treo. Ideally I'd like a stereo headset so I can listen to music as well.

Let's say I do get such a headset, how will I assign VC initiation to it? Will a new button appear under Settings -> Buttons that I can assign to? Currently there are phone specific buttons only (Start, OK, Opt+Start, Opt+OK, Side, and Opt+Send).

ps: I have MS VC 1.5 which came installed on the phone - should I upgrade to 1.6? What new features are there?

[dping28]

I have a Sprint PPC-6700 with AKU 3.3 and MSVC 1.6 and when I installed this (everything to main memory) it installed. I soft reset and when the phone boots up i get a beep in my headset and then a popup that says:

IDTransfer.exe
The file 'IDTransfer' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. You might need to reinstall or restore this file.

It said in the first thread that .net 2 was no longer needed. Is there something else I need installed?? Thanks!!

-D

[fibrolan]

Hi,

I am new to this forum. Can you pls explain to me your program. i am using a HP 6955 with a motorola H700 headset. What is the difference between your program and me setting the audio checkmark under the bluetooth setting to allow everything to come through the headset ?

Fibrolan

[losborn]

After testing with the 8525 I've determined that VC is NOT "opening" the Bluetooth "circuit." With .9f and IDTransfer installed VC announces the call to the speaker, then, when I touch the answer button on the headset, I hear 3-4 seconds of announcement in the headset before the call is answered (what's up with that, BTW? I have to remember to wait until the announcement stops before I say "Hello!") More experimentation shows that audio from various sources - Windows Media, Beta Player, whatever - goes to the speaker until I MANUALLY "open" the Bluetooth audio "circuit" by pressing the button on the headset, whereupon the audio goes to the headset until the "circuit" times out, when it returns to the speaker.

Does anyone have any ideas how to make VC "open" the Bluetooth audio "circuit?"

[blakepea]

Program works great. Is there a way to remove the beeping that occurs on an incoming call?

[leepriestenator]

Originally Posted by losborn

Does anyone have any ideas how to make VC "open" the Bluetooth audio "circuit?"

1) You have to understand that ID Tranfer only send the VC announcement and the ringer to the headset.

2) When you press the button on your headset, the audio gateway is routed to the headset. Hence you can hear all system sounds including WMP on the headset. As soon as it times out, the audio goes back to the phone.

3) ID Transfer comes with a small file called Audio.exe which is placed in the start menu. This file, when activated routes all the phone's audio (including system sounds) to the headset. It stays routed to the headset till the button on the headset is pressed again.

4) To activate this Audio.exe using VC, just press the button on your headset and say "OPEN AUDIO" or START AUDIO". This will excecute the Audio.exe file and route all the audio to the headset till you press the button on the headset again.[/b]

[greatnate]

Originally Posted by leepriestenator

1) You have to understand that ID Tranfer only send the VC announcement and the ringer to the headset.

2) When you press the button on your headset, the audio gateway is routed to the headset. Hence you can hear all system sounds including WMP on the headset. As soon as it times out, the audio goes back to the phone.

3) ID Transfer comes with a small file called Audio.exe which is placed in the start menu. This file, when activated routes all the phone's audio (including system sounds) to the headset. It stays routed to the headset till the button on the headset is pressed again.

4) To activate this Audio.exe using VC, just press the button on your headset and say "OPEN AUDIO" or START AUDIO". This will excecute the Audio.exe file and route all the audio to the headset till you press the button on the headset again.[/b]

Audio.exe does not work on the 8525; this is the result of the problem or the problem depending on how you look at it.

[hit93]

I'm too having the same issue as stated below. Has anyone found a fix to this. Please help.

Originally Posted by dping28

I have a Sprint PPC-6700 with AKU 3.3 and MSVC 1.6 and when I installed this (everything to main memory) it installed. I soft reset and when the phone boots up i get a beep in my headset and then a popup that says:

IDTransfer.exe
The file 'IDTransfer' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. You might need to reinstall or restore this file.

It said in the first thread that .net 2 was no longer needed. Is there something else I need installed?? Thanks!!

-D