Turn no2chem's ROM into a kitchen?

[miguelfp1]

Originally Posted by saumaun

Thanks for all the responses. I did all the steps mentioned above, however, when I run ROMupdateutility it crashes. Nothing gets flashed to the phone...

I'll wait for no2chems next basekit and try it from there. Thanks for all of your help!

THis may or may not help, but have you tried flashing from a memory card? I find it's much faster than flashing via USB...

[TurboFool]

I'm quite curious about this flashing-from-a-memory card bit. I noticed this "NueUpdate" function of the latest ROM, and now you're mentioning it. How is this achieved?

[vclawson]

Originally Posted by bblanski

This is how I finally got it to work. I am a newbie so dunno if this is the right way but it worked for me.

1. Download basekit
2. Download dogguy kitchen
3. Remove oem, rom, sys folders(also there should be no nbh file, if there is remove it. Not sure if you have to but that is what I did.)
4. Copy and past the oem, rom, sys folders from basekit to dogguy kitchen.
5. Add what you want to the oem file
6. Run buildos and check what you want.
7. Run buildit
8 Run ruu.
After the ruu runs it takes a bit to load, the latest does not have a welcome screen so you will have to tap on the white screen to complete setup. Hope this helps

I just tried this without putting in any OEM's. Everything works until I run the RUU which just crashes. Any idea why?

[azclown]

Originally Posted by no2chem

using basekit should work. at least it should work with buildos. i don't really have the time to support custom kitchens, but the basekit should make it a drag and drop kind of thing for most kitchens, especially since i include the rom folder now.

Between what you said No2chem and BBlanski i have managed to make a ROM from the basekit. I have been able to add a bunch of stuff i want to use... some items are going to require alot more tinkering to get the bugs worked out so they can be integrated into the rom, but with folks like these around it shouldn't be an issue.... Thx again for the help, I do appreciate it, and your patience with my noob questions...

Thx
D

[azclown]

Originally Posted by vclawson

I just tried this without putting in any OEM's. Everything works until I run the RUU which just crashes. Any idea why?

what I did was simple. Just like bblanksi said, replace the Kitchen folders with no2chems base kit. then just run the buildos.bat, you shouldn't get any errors from this. then run the buildit.bat. that should finish without any errors too.... when you get to this point, you will have a .nbh file around 54 megs.... this should flash just fine.... Now you can go back and add all the custom stuff you want but this is where the reg issues come in, you are going to have duplicate file issues and sometimes registry issues, this is where i am at, hunting down how to fix the issues and still have the apps work properly....

good luck

[bblanski]

Originally Posted by vclawson

I just tried this without putting in any OEM's. Everything works until I run the RUU which just crashes. Any idea why?

Is there a nbh file in the ruu when you go to run it? also are you synced to the computer. I am completely new to this stuff also, been messing around and reading all I can for two weeks. Been using dcd's stuff and no2chem's stuff and it has been trial and error for the most part. Big thanks to both of those guys for all the work, dogguy also. I can only imagine how much time they put in after all the time I spend messing with it.

[vclawson]

Originally Posted by azclown

what I did was simple. Just like bblanksi said, replace the Kitchen folders with no2chems base kit. then just run the buildos.bat, you shouldn't get any errors from this. then run the buildit.bat. that should finish without any errors too.... when you get to this point, you will have a .nbh file around 54 megs.... this should flash just fine.... Now you can go back and add all the custom stuff you want but this is where the reg issues come in, you are going to have duplicate file issues and sometimes registry issues, this is where i am at, hunting down how to fix the issues and still have the apps work properly....

good luck

The problem is when I try to flash it. Yes, I do have a .nbh file in the RUU folder and the update utility comes up. It indicates that it is going to update to DogGuy 2.17 and then crashes.

[vclawson]

ok, my problem is in the Buildit. This is what I get:
Could not open input file '..\ROM\8004000-OS.nb'. Aborting.
.... Done.
Building new imgfs.bin from dump...
The system cannot find the path specified.
Could Not Find C:\Users\clawsonv\Downloads\DogGuy Kitchen\Temp2\imgfs.old.bin
.... Done.
Building OS-new.nb...
Could Not Find C:\Users\clawsonv\Downloads\DogGuy Kitchen\Temp2\imgfs.bin
Could Not Find C:\Users\clawsonv\Downloads\DogGuy Kitchen\Temp2\OS.nb.payload
The system cannot find the file specified.
The system cannot find the file specified.
.... Done.
Building RUU_signed.nbh...
NBH Generator ver0.1 by bot

os-new.nb
Completed.
.... Done.
Clean up time!
The system cannot find the file specified.
1 file(s) moved.
.... Done.
BuildIt is Complete.
Flash your new RUU_Signed.nbh, and enjoy!
Press any key to continue . . .



Any idea why I would be getting this?

[azclown]

Ya, I had that too. DO NOT RUN the Prepit.bat file..... Taker No2chems BASE KIT and put the SYS, OEM, and ROM folders into the kitchen folder, you WILL replace the ones that were in there. The run the buildos.bat file. You should have no errors. Then run builtit.bat file.... When that is done goto the RUU folder and you should see a file name RUU_signed.nbh that is about 54 megs. Now from here, take your phone and press the POWER and CAMERA button and hold them, and then press and hold the reset button by the SD card. After~2 secs you should see the bootloader screen, should be 3 colors bars on it with some text. Now you can just plug your phone into the USB port and then run the ROMUpdateUtility.exe, and follow the directions..... Hope this helps ya....

[miguelfp1]

Originally Posted by TurboFool

I'm quite curious about this flashing-from-a-memory card bit. I noticed this "NueUpdate" function of the latest ROM, and now you're mentioning it. How is this achieved?

Well, it's quite easy. First you need to format a memory card to FAT32 (it HAS to be fat32). Transfer your built .NBH to the card, rename it to TITAIMG.nbh, insert the card in the phone and put it in bootloader mode (hold Power + Camera and hit the reset button), the loader will automatically find the image and ask if you want to perform the update.

I hope I was clear enough and that the instructions help.