Obtaining MSL

[gsvnet]

Originally Posted by sublinx

Did you ever find a MLS code to unlock your phone? I been trying mine for about the last 4 hours trying different ways of using GetSPC and no code it gives me works. If you figured out a way please let me know.

I've concluded that GetSPC just won't work. But you can try Sprint's chat system (assuming that's your carrier...).

[akared]

I just did a sprint chat session gave them my number and said i needed to reset my new phone due to signal issues, and I had done it on my old phone and it fixed the issue. She gave it to me

[sublinx]

Originally Posted by Brock1909

this is the only way that has worked for me

After I do what you have said and soft reset and make sure the changes stuck in my registry, I have an Atlog folder and a txt file that is ATDbg0. I tried using the code next to the characters you said and it still tells me wrong code. What could I be doing wrong? The getspc didn't work for me as well.

[gsvnet]

Originally Posted by sublinx

After I do what you have said and soft reset and make sure the changes stuck in my registry, I have an Atlog folder and a txt file that is ATDbg0. I tried using the code next to the characters you said and it still tells me wrong code. What could I be doing wrong? The getspc didn't work for me as well.

How long is this code? Are you sure it is valid?

[sublinx]

Originally Posted by gsvnet

How long is this code? Are you sure it is valid?

I'm at idiot. I finally got it. Worked great as stated. Thanks.

[sublinx]

I have done everything that I can think of. I have gotten to the metropcs prl. If I try to make a call I get Metropcs and if I dial *228 it takes me to MetroPCS. My phone still says Sprint as the carrier logo. What else do I need to do? Any help would be great.

[twospirits]

Originally Posted by ilkevinli

Use this method. I don't know who found it, but credit goes to them.

Change the following registry entries in:
HKEY_LOCAL_MACHINE\SOFTWARE\HTC\ATDbgLog
Enable: 1
LogMode: 1
* Wait a reasonable amount of time and soft-reset (I have noticed that it seems to take longer for this value to take affect, so if you reboot and the registry values are not changed, then you need to do it again and wait longer)
* Check to see that the file \ATDbg0\ATDbg0.txt has been created.
* Return the values back to what they were (most likely 0) waiting the same amount of time as above.
* Look in the ATDbg0.txt file and you should see a log of commands sent to the CDMA radio and there should be something like this somewhere in the file:
|| Begin Code Sample ||
11:9:3 Tx:AT+HTC_RMSL=0\r
11:9:3 Rx:+HTC_RMSL: 354201\r\n0\r
11:9:3 Tx:AT+HTC_ROTKSL=0\r
11:9:3 Rx:+HTC_ROTKSL: 216112\r\n0\r
|| End Code Sample ||
The numbers next to the Rx: +HTC_RMSL line should be your MS

This method worked perfectly. I have two Diamonds and the GetSPL file kept giving me different results. One of which was completely different from what CS gave me.
Only difference with this method is that the resulting ATDbg0.txt was created one level up.
TS

[sublinx]

Well I have loaded the latest MetroPCS prl and just wanted to know if anyone had the NAM settings or is that something that MetroPCS does?

[clockcycle]

I went to the Sprint Store asked the girl at the counter for mine, done.. No hassles, no questions (other than info to get into your account).

-CC

[rawdikrik]

Originally Posted by ilkevinli

Use this method. I don't know who found it, but credit goes to them.

Change the following registry entries in:
HKEY_LOCAL_MACHINE\SOFTWARE\HTC\ATDbgLog
Enable: 1
LogMode: 1
* Wait a reasonable amount of time and soft-reset (I have noticed that it seems to take longer for this value to take affect, so if you reboot and the registry values are not changed, then you need to do it again and wait longer)
* Check to see that the file \ATDbg0\ATDbg0.txt has been created.
* Return the values back to what they were (most likely 0) waiting the same amount of time as above.
* Look in the ATDbg0.txt file and you should see a log of commands sent to the CDMA radio and there should be something like this somewhere in the file:
|| Begin Code Sample ||
11:9:3 Tx:AT+HTC_RMSL=0\r
11:9:3 Rx:+HTC_RMSL: 354201\r\n0\r
11:9:3 Tx:AT+HTC_ROTKSL=0\r
11:9:3 Rx:+HTC_ROTKSL: 216112\r\n0\r
|| End Code Sample ||
The numbers next to the Rx: +HTC_RMSL line should be your MS

This is the way to do it. Ive done it and it works perfectly... and only takes about 20 mins tops and no cabs or software to install.

You beat me to the posting...