Treo Pro CDMA HardSPL

[mackdaddy1]

Can someone please help I think i just brick my my phone.
I tried going back to 6.1 and i got an error message stating
pant200
SPL-0.36.CMONEX
CPLD-2

Upgrade ROM code error please try again (and it wont go away)

I try doing a soft reset and a hard reset with no luck

can someone please help

[acidhax]

Originally Posted by mackdaddy1

Can someone please help I think i just brick my my phone.
I tried going back to 6.1 and i got an error message stating
pant200
SPL-0.36.CMONEX
CPLD-2

Upgrade ROM code error please try again (and it wont go away)

I try doing a soft reset and a hard reset with no luck

can someone please help

No you didn't brick your phone :P

Get back in to the SPL screen (Hold the Camera + Power button and reset phone), and run the 6.1 ROM installer again.

[mthstc]

dear,
My Sprint Treo Pro already had:
PANT200
SPL-0.36.0000
CPLD-2
Is that newest version or yours?
Thanks

[DssTrainer]

So if I do a hard reset on my phone, it resets the HSPL too ? I don't remember that happening on the HTC Touch.

Anyway, I'll have to do this step again I guess as it is showing 0.32 instead of 0.36 after i did a hard reset. I'm trying the SD method but that does nothing.

1. Download HSPL
2. Rename from ruu_unsigned.nbh to PANTIMG.NBH
3. Copied to my phone storage card (root)
4. Ran the Manual SSPL program (also in root)
5. I get tricolor screen.... and it just sits there
6. I read elsewhere that you need to press the power button at the tricolor screen but that didn't work either

[budney]

Originally Posted by DssTrainer

So if I do a hard reset on my phone, it resets the HSPL too ? I don't remember that happening on the HTC Touch.

No it will not reset/reverse the HSPL if you hard reset. If like any other HTC device.

[juttonn]

Originally Posted by DssTrainer

So if I do a hard reset on my phone, it resets the HSPL too ? I don't remember that happening on the HTC Touch.

Anyway, I'll have to do this step again I guess as it is showing 0.32 instead of 0.36 after i did a hard reset. I'm trying the SD method but that does nothing.

1. Download HSPL
2. Rename from ruu_unsigned.nbh to PANTIMG.NBH
3. Copied to my phone storage card (root)
4. Ran the Manual SSPL program (also in root)
5. I get tricolor screen.... and it just sits there
6. I read elsewhere that you need to press the power button at the tricolor screen but that didn't work either

I'm getting the same result. I bought the Treo Pro for my wife on ebay and it didn't come with a USB cable. The other thing I tried was going into the boot loader (hold down power and camera button and then pushing soft reset button). When I do that i briefly get the tri-color screen, then the screen goes gray and says "Loading..." But it hangs there forever (I left it there for 30 minutes or so).

I tried redownloading files, I made sure the SD card is fat32, etc. Anyone have any other ideas? Thanks

[skeegcpp]

Originally Posted by juttonn

tried redownloading files, I made sure the SD card is fat32, etc. Anyone have any other ideas? Thanks

make sure the PANTIMG.nbh is on the root and that there isn't any other files like it on the root...cuz it sounds like its trying to update 2 files or sumthin
now when unlocking via sd card, at the end it mite jus say loading on the screen or give u a rom update error..ignore it, soft reset and cee what ya get

[DssTrainer]

Originally Posted by juttonn

I'm getting the same result. I bought the Treo Pro for my wife on ebay and it didn't come with a USB cable. The other thing I tried was going into the boot loader (hold down power and camera button and then pushing soft reset button). When I do that i briefly get the tri-color screen, then the screen goes gray and says "Loading..." But it hangs there forever (I left it there for 30 minutes or so).

I tried redownloading files, I made sure the SD card is fat32, etc. Anyone have any other ideas? Thanks

Same issue here. the SD load method worked fine for roms when its already 0.36 but when its 0.32 and you are trying to load the hardspl.. it does nothing.

[jaypro]

Hey DS.. I'm not sure how to thank you enough. I'm simply amazed that you've taken the time to go in details about answering my (so many) questions. It's indeed people like you who makes a big (and very positive) impact in these forums, and who offer hopes for desperate people like myself. I will follow or your instructions and keep you posted on the results.
Thanks again))

[relisted]

umm the HSPL will not work for me.
it says
RAPI.dll was not found try reinstalling blahh

anyone else get this??