Hard-SPL - Flashing ROMs - Titan Unlocker - Click Here!

[dan-htc-touch]

you may not have the correct radio for the bootloader and rom you are running. when it's booting, there will be an r and next to it should read 3.35 or higher

[puff]

Originally Posted by jmann91

After using Oilpro to unlock my Sprint Mogul I was able to successfully use BuildOS to upload the No2Chem ROM to my device. Everything seemed to work properly the phone did its normal boot and start-up after an update and the bootloader screen is gone.

Problem is once I unplug the phone from USB the device will run fine for about 30 to 45 seconds then reboot. It boot back into normal mode but 45 seconds later it will reboot again. Plugging it back into the USB stops the re-booting.

What do I need to do to fix this problem?

John

Yeah, like dan said sounds like you need a radio update to 3.35 or higher

[puff]

Originally Posted by Bad Sector

Tested it just again to make sure that worked, and it does! Everytime I hit reset, I get shot to bootloader..

To get out of Bootloader I do the following:
set 14 0
set 16 0
task 8

unplug phone, remove battery, replace after 30 sec, plug in usb cable and wait for yellow light. Press and hold power for 1 sec or so till it boots.

Atleast I have an escape method now

wow, never had that problem
bootloadr shows 2.40?

[cardriver]

i still have this issue even after "upgrading" to the n2cs bootloader so im lost. i can still get around but its a pain

[Bad Sector]

PPC Noob, Yes, bootloader is 2.40-Olipro .
I still need to find a way to get this phone back to stock and flash with the Official roms... but everyone is scaring me... I don't want to brick this thing for good.

But I can't soft reset with out getting kicked to bootloader, and that will be a real pain if I am some where without my laptop...

I may just go for it..... still debating...

[puff]

Originally Posted by Bad Sector

PPC Noob, Yes, bootloader is 2.40-Olipro .
I still need to find a way to get this phone back to stock and flash with the Official roms... but everyone is scaring me... I don't want to brick this thing for good.

But I can't soft reset with out getting kicked to bootloader, and that will be a real pain if I am some where without my laptop...

I may just go for it..... still debating...

You can revert to stock bootloader with no2chem's relocker...
here's a link -> http://forum.ppcgeeks.com/showthread.php?t=30560

[evilbeef54]

Thanks for all the hard work guys, i tried the unlocker, got stuck at the RGB screen same as everyone else, didn't read enough to figure out how to disable activesync to run the exe in "stuck at bootloader screen, so i ended up just re-running the wm6.1 RUUand of course since im a noob i didn't know how to check to see if the unlocker fully worked so i ran the wm6.1 ruu one more time and bootloader screen still says olipro2.4 so it sounds like it worked thanks guys i cant wait to try some of these custom roms

[sabonis]

Sorry if this is a re post, but xp is too small a word to come up in search. I have xp 64. when I tried to use olipro 2.40, it said not compatible with xp 64 and to request a 64 bit addition of the software. Am I s.o.l.? Thanks

[cornelious2]

Originally Posted by sabonis

Sorry if this is a re post, but xp is too small a word to come up in search. I have xp 64. when I tried to use olipro 2.40, it said not compatible with xp 64 and to request a 64 bit addition of the software. Am I s.o.l.? Thanks

use nueSPL from an sd card.

[sabonis]

Thanks, that worked great. Thanks for the quick response!