Android For The Vogue Is Here!!!

[kiddk1]

well putting the files on the sd card did not work for me so i used the cab android install and swapped the initrd and zimage with the updated ones and it worked. My question is how do i improve the screen reslolution, the cab file did not create a default.txt, it did create a startup.txt as follows

set RAMSIZE 0x08000000
set MTYPE 1667
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.username - The username used to connect to the network when dialing #777
# ppp.password - The password used to connect to the network when dialing #777
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 0, use 3 if you have an old radio
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 0=Don't power off the panel (Default)
# 1=Hitachi 2=Topoly 3=Samsung
#
set cmdline "ppp.username=mobile@jamamobile ppp.password=telecom"
# This is what I use: "msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 board-htcvogue.panel_type=1"
boot

[ali3nfr3ak]

Originally Posted by kiddk1

well putting the files on the sd card did not work for me so i used the cab android install and swapped the initrd and zimage with the updated ones and it worked. My question is how do i improve the screen reslolution, the cab file did not create a default.txt, it did create a startup.txt as follows

set RAMSIZE 0x08000000
set MTYPE 1667
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.username - The username used to connect to the network when dialing #777
# ppp.password - The password used to connect to the network when dialing #777
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 0, use 3 if you have an old radio
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 0=Don't power off the panel (Default)
# 1=Hitachi 2=Topoly 3=Samsung
#
set cmdline "ppp.username=mobile@jamamobile ppp.password=telecom"
# This is what I use: "msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 board-htcvogue.panel_type=1"
boot

this is for HERO build

set RAMSIZE 0x08000000
set MTYPE 1667
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.nostart - Set ppp.nostart=1 to disable starting the ppp connection on boot
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 3, use 0 for best power savings
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 1=Hitachi 2=Topoly 3=Samsung
# clock-7x00.mddi - MDDI clock (try 0xa51 or 0xe2c)
# clock-7x00.ahb_div - Advanced Host Bus divider, default is 4
# 2 is faster but uses more power
# clock-7x00.a11 - ARM11 clock speed in MHz, best to leave this alone
# lcd.density - Defaults to 160, 128 shows more on screen
# vogue-ts.XMIN - xmin value for the touchscreen calibration. Also YMIN, XMAX, YMAX, PMIN, PMAX.
#
# Probably the only one of these you will need to change is the panel type, NZ Vogues seem to all have type 1
# US Sprint vogues usually have type 2 or 3 I think.
# Make sure you add these between the quotes on the following line and that your editor hasn't split the line up.
set cmdline "ppp.nostart=0 ppp.username=mobile@jamamobile ppp.password=telecom mddi.width=320 mddi.height=480 lcd.density=160 msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 board-htcvogue.panel_type=1 no_console_suspend"
boot

this is for Donut/tatto

set RAMSIZE 0x08000000
set MTYPE 1667
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.nostart - Set ppp.nostart=1 to disable starting the ppp connection on boot
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 3, use 0 for best power savings
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 1=Hitachi 2=Topoly 3=Samsung
# clock-7x00.mddi - MDDI clock (try 0xa51 or 0xe2c)
# clock-7x00.ahb_div - Advanced Host Bus divider, default is 4
# 2 is faster but uses more power
# clock-7x00.a11 - ARM11 clock speed in MHz, best to leave this alone
# lcd.density - Defaults to 160, 128 shows more on screen
# vogue-ts.XMIN - xmin value for the touchscreen calibration. Also YMIN, XMAX, YMAX, PMIN, PMAX.
#
# Probably the only one of these you will need to change is the panel type, NZ Vogues seem to all have type 1
# US Sprint vogues usually have type 2 or 3 I think.
# Make sure you add these between the quotes on the following line and that your editor hasn't split the line up.
set cmdline "ppp.nostart=0 ppp.username=mobile@jamamobile ppp.password=telecom mddi.width=240 mddi.height=320 lcd.density=120 msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 board-htcvogue.panel_type=1 no_console_suspend"
boot

[kiddk1]

thanks, will try it out.

[urgodfather]

so... exactly which build is best to use? i have seen mixed things about donut, cupcake, tattoo, and sensehero... but its all vague about which one is better. especially since one of the devs. is for both and they comment that they like both.

next question, how would one go about completely omitting the winmo rom and do a complete switch? has this be done? basically im saying can we flash it to the ppc? i mean it is open source.....

[ds--]

has anyone gotten the android build on xv6900 to work with ms exchange?

[ss0mohit]

no. in case if you need to back up data and exchange contacts. there's been a way.
http://forum.ppcgeeks.com/showthread.php?t=94504

creds to giggles312

[mfpreach]

Originally Posted by urgodfather

so... exactly which build is best to use? i have seen mixed things about donut, cupcake, tattoo, and sensehero... but its all vague about which one is better. especially since one of the devs. is for both and they comment that they like both.

next question, how would one go about completely omitting the winmo rom and do a complete switch? has this be done? basically im saying can we flash it to the ppc? i mean it is open source.....

Use 1.5 Ion , it is extremly fast, has gps and bluetooth and is very stable.
Hero is molasses, even the new ones they say are fast. Donut is fine but no GPS and not necessarily much diff from 1.5.

[kiddk1]

can you link me to 1.5 ion?

[ss0mohit]

how would you exactly switch?
my android platform works perfectly, if not faster than wm. but i have the ion build. i have everything saved in the user.conf folder.

[ali3nfr3ak]

Originally Posted by kiddk1

can you link me to 1.5 ion?

http://search.4shared.com/network/se...lue=10&start=0