Quote:
Originally Posted by kiddk1
well putting the files on the sd card did not work for me so i used the cab android install and swapped the initrd and zimage with the updated ones and it worked. My question is how do i improve the screen reslolution, the cab file did not create a default.txt, it did create a startup.txt as follows
set RAMSIZE 0x08000000
set MTYPE 1667
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.username - The username used to connect to the network when dialing #777
# ppp.password - The password used to connect to the network when dialing #777
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 0, use 3 if you have an old radio
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 0=Don't power off the panel (Default)
# 1=Hitachi 2=Topoly 3=Samsung
#
set cmdline "ppp.username=mobile@jamamobile ppp.password=telecom"
# This is what I use: "msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 board-htcvogue.panel_type=1"
boot
|
this is for HERO build
set RAMSIZE 0x08000000
set MTYPE 1667
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.nostart - Set ppp.nostart=1 to disable starting the ppp connection on boot
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 3, use 0 for best power savings
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 1=Hitachi 2=Topoly 3=Samsung
# clock-7x00.mddi - MDDI clock (try 0xa51 or 0xe2c)
# clock-7x00.ahb_div - Advanced Host Bus divider, default is 4
# 2 is faster but uses more power
# clock-7x00.a11 - ARM11 clock speed in MHz, best to leave this alone
# lcd.density - Defaults to 160, 128 shows more on screen
# vogue-ts.XMIN - xmin value for the touchscreen calibration. Also YMIN, XMAX, YMAX, PMIN, PMAX.
#
# Probably the only one of these you will need to change is the panel type, NZ Vogues seem to all have type 1
# US Sprint vogues usually have type 2 or 3 I think.
# Make sure you add these between the quotes on the following line and that your editor hasn't split the line up.
set cmdline "ppp.nostart=0 ppp.username=mobile@jamamobile ppp.password=telecom mddi.width=320 mddi.height=480 lcd.density=160 msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 board-htcvogue.panel_type=1 no_console_suspend"
boot
this is for Donut/tatto
set RAMSIZE 0x08000000
set MTYPE 1667
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.nostart - Set ppp.nostart=1 to disable starting the ppp connection on boot
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 3, use 0 for best power savings
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 1=Hitachi 2=Topoly 3=Samsung
# clock-7x00.mddi - MDDI clock (try 0xa51 or 0xe2c)
# clock-7x00.ahb_div - Advanced Host Bus divider, default is 4
# 2 is faster but uses more power
# clock-7x00.a11 - ARM11 clock speed in MHz, best to leave this alone
# lcd.density - Defaults to 160, 128 shows more on screen
# vogue-ts.XMIN - xmin value for the touchscreen calibration. Also YMIN, XMAX, YMAX, PMIN, PMAX.
#
# Probably the only one of these you will need to change is the panel type, NZ Vogues seem to all have type 1
# US Sprint vogues usually have type 2 or 3 I think.
# Make sure you add these between the quotes on the following line and that your editor hasn't split the line up.
set cmdline "ppp.nostart=0 ppp.username=mobile@jamamobile ppp.password=telecom mddi.width=240 mddi.height=320 lcd.density=120 msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 board-htcvogue.panel_type=1 no_console_suspend"
boot