Titan stuck on sub splash

[gTen]

I guess then there is nothing you can do other then:

1) Try pressing the camera button really hard and hope it works after X attempts of trying to enter bootloader (you never know when a press from soem random direction somehow makes it work once or soemthing)

2) Take apart your phone and fix/simulate the camera button press (Since buttons work pretty simple switch mechanics, but I wouldn't do this unless you have at least basic understanding of circuitry)

3) Take it in for repairs

[drewcam888]

Verizon doesn't do repairs. If you have insurance they swap it out free. Hopefully you have a stock splash screen. If not that might see you voided extended warranty. Then you would have to file an insurance claim.

[bem]

This thread is the closest I have found to describing my problem. It is going to be long winded so here we go:

I have been watching and reading about upgrading my uscc 6800 for about 6-8 months now and yesterday I took the plunge.

I used the upgrade instructions that were spelled out here: http://ppcgeeks.com/forum.ppcgeeks/s...ad.php?t=24511

I followed the directions, or so I thought. I ran the hard-spl-mfg.exe and everything was working just fine. After following the on screen instructions the program ran the RUU program. I had read ahead in the instructions and didnt think this needed to be ran until I was ready to copy my os rom onto the phone.

This is where I really messed up and I am hoping I didnt mess it up for good.

I ran the RUU with the cooked os rom and installed it on my phone. Now my phone only boots to the sub splash screen.

As best as I can tell this is because I didnt actually "commit" or permanently copy the unlocked bootloader onto the phone and also because the radio did not get upgraded.

From what I am reading I think all I really need is the nhb file that is created from the nueSPL-2.47 unlocker, but I am not sure. I think from there I can reflash the os rom and radio appropriately. My big problem is that since I cannot connect the phone to activesync I cannot run any of those type of unlockers and since my phone will not boot into windows mobile i cannot run the nueSPL-2.47.exe either.

If someone can provide some direction or provide the nhb file that would be greatly appreciated.

My current phone specs:

USCC 6800
ROM: winmo 6.5 (latest build available in buildos)
Radio: 1.64.00
Protocol: ACAAAAM-4070

The first splash screen shows the following

NueKernel-3.01
build 109 (c) 2008 No2Chem
Low mem (camera enabled)


M 09 P ACAAAAM-4070
B 03 R 1.64.00
D 3.56

Thank you to any and all in advance for all of your help.
-Brent

[drewcam888]

Yes you need to install a radio by sd card method. If you installed 6.5 then the bootloader isn't the problem but you forgot a gps radio for the gps 6.5 rom.

[bem]

this will allow the phone to boot even though it still has the old bootloader?

[drewcam888]

You can't install the 6.5 rom without an unlocked bootloader. So you bootloader should be fine. Hold camera, power, and reset for 5 seconds and see what version you have.

[drewcam888]

You were supposed to install the gps radio before installing the rom.

[bem]

yea i know that now, i guess i didnt quite grasp the difference between the three parts (bootloader, radio, os roms).

at the bootloader screen it reads

TITA100
SPL-1.07.0000
CPLD-9

When I ran the hard-spl utility on my xp box it did reboot my phone with the 2.40 bootloader, but i guess since i didnt run the ruu that it prompted the new bootloader wasnt actually installed.

[drewcam888]

Ok so that bootloader is a problem. So put phone in bootloader and rerun 2.40 unlocker. Then install radio by sd method.

[bem]

i am attempting to run the 2.40 unlocker right now. thanks