PPCGeeks - Unrecognized USB device during ActiveSync (helmi's WM6)

Page 4 of 5

« First

Show 40 post(s) from this thread on one page

PPCGeeks (http://forum.ppcgeeks.com/index.php)

- HTC Apache Development (http://forum.ppcgeeks.com/forumdisplay.php?f=53)

- - Unrecognized USB device during ActiveSync (helmi's WM6) (http://forum.ppcgeeks.com/showthread.php?t=8336)

Raistlin5

11-08-2007 07:06 PM

i'm gonna try using bluetooth to connect to activesync...

Raistlin5

11-08-2007 07:48 PM

i can't win... got bluetooth connection to activesync,ran romupdate exe and phone got disconnected and is now stuck in bootloader mode...

Raistlin5

11-08-2007 08:02 PM

life may be good.... in bootloader mode my usb works!!!! romupdate running and installing new kitchen.... keeping my fingers crossed.Will let you know if it works

Kolano

11-08-2007 08:08 PM

This thread at XDA-Developers offers a bit more insight as to what ActivesyncMode does.

Raistlin5

11-08-2007 08:36 PM

Life is good !!! Everything works got the new kitchen installed !!
Thanks to Helmi and everyone who contributes to this awesome forum !!!

guitardoc64

11-09-2007 03:24 AM

Quote:

Originally Posted by Raistlin5 (Post 117329)

i can't win... got bluetooth connection to activesync,ran romupdate exe and phone got disconnected and is now stuck in bootloader mode...

you tried to flash a ROM over BT?!?!? is that even possible? I'd NEVER trust anything but a hardwire connection for doing any updating as deep as a ROM upgrade.

Raistlin5

11-09-2007 07:08 PM

I ended up using usb while in bootloader mode

guitardoc64

11-09-2007 08:23 PM

Quote:

Originally Posted by Raistlin5 (Post 118264)

I ended up using usb while in bootloader mode

It's the only way. Bootloader and usb are the only way to do it. Bluetooth is software supported and gets turned off with everything else that's being replaced when the ROM is being upgraded.

bilson

11-23-2007 03:28 PM

Have same problem USB Device Not Recognized error and tried almost all mentioned fixes, but found when left alone the error goes away usually in less than a minute and all works find. Now after reburning with Helmi_c newest Kitchen of 11/17 and the PPCGeeks oems I can't get Bluetooth to access Activesync. Activesync is not listed as an option on the phone, just serial port and dialup networking.

DocHoskins

11-23-2007 04:52 PM

Quote:

Originally Posted by guitardoc64 (Post 89156)

Try getting activesyncmode from UTStarcomm. there are a couple ways to get it, but it will download and install with PIE. It fixes the unrecognised device error.

On the PDA, open Internet Explorer and type the address http://www.utstar.com/pcd/downloads/...yncmode.sa.cab
Select “Save As” into Storage card or Main Memory, then OK,
it will automatically install to the device
After install, Close all programs on the device
Tap Start, then select Programs, and then Active Sync Mode
Switch from RNDIS to USB, then tap OK
Close all programs then Sync with your computer.

Worked like a charm. The url posting on this forum left out some letters, but just had to look at the status bar on my browser to see the entire link.

This has been a problem since I got the phone. I usually just had to power cycle the phone to work. Not today...then I come here to see THE solution. Thanks.

All times are GMT -4. The time now is 02:32 AM.

Page 4 of 5

« First

Show 40 post(s) from this thread on one page

Content Relevant URLs by vBSEO 3.6.0