[BUILD] **Complete Froyo Bundle!!** FRX06 - "Stable" - Minor Fixes

[n1nj4Lo]

I'm sure a lot of simple stuff Q's & A's could be ccp'ed from this thread over to the wiki. LoL

Theres enough questions being asked here to base a F.A.Q. Wiki off of.

[Recursion]

Originally Posted by arrrghhh

Today, in fact! I'm not too hard on the newbies... am I? . Plus, I don't think there are any stupid questions - I try to put everything that's needed in the first post, just let me know if something is worded funny.

Nah, not at all. Good job with the directions, simple. Btw, you might wanna add "1. Pull Sim Card." I got snagged on that one...lol.

[arrrghhh]

Originally Posted by Recursion

Nah, not at all. Good job with the directions, simple. Btw, you might wanna add "1. Pull Sim Card." I got snagged on that one...lol.

Heh, I'll add that to the FAQ. Not many people have a SIM installed if they use CDMA .

I'm trying to keep the first post as clean as possible - the more text I put in there, the less people are going to want to read it...

[n1nj4Lo]

Okay oops

When editing it where would I put "rel_path=et cetera" in the list, or any particular order, I'm assuming I can't just put it anywhere in the startup.txt list...

I'm thinking it would be done like

set ramsize 0x10000000
set ramaddr 0x10000000
set mtype 2292
set KERNEL zImage
set initrd initrd.gz
set cmdline "lcd.density=240 msmvkeyb_toggle=off gsensor_axis=2,1,3 force_cdma=1 pm.sleep_mode=1 physkeyboard=rhod400"
rel_path=et cetera
boot

Correct or does it matter?

[arrrghhh]

Originally Posted by n1nj4Lo

Okay oops

When editing it where would I put "rel_path=et cetera" in the list, or any particular order, I'm assuming I can't just put it anywhere in the startup.txt list...

I'm thinking it would be done like
Correct or does it matter?

Yea, I'm struggling with how to make this more clear.

Basically it goes within the quotes on the cmdline section. It doesn't matter where on the cmdline section, as long as it's between the quotes and there's a space between each item...

set ramsize 0x10000000
set ramaddr 0x10000000
set mtype 2292
set KERNEL zImage
set initrd initrd.gz
set cmdline "lcd.density=240 msmvkeyb_toggle=off gsensor_axis=2,1,3 force_cdma=1 pm.sleep_mode=1 physkeyboard=rhod400 rel_path=FRX04"
boot

^^ like that.

I'm open to ideas on how to explain this better... I've always struggled with how to explain exactly where it goes, and many have made the same mistake you did...

[n1nj4Lo]

Errr still nothing it gets so far and then comes to a complete halt with the mdr busy error...

I'm gunna try moving everything directly onto the root of the card and if that doesn't work I'm gunna give up till I get my 32Gb.

I believe this card FAT32, I just don't wanna move 14Gb's worth of stuff over to the pc and then back over to the card again.
_

Would it being plugged in and charging cause any possible problems usb or ac?

[ndno]

Originally Posted by n1nj4Lo

Okay oops

When editing it where would I put "rel_path=et cetera" in the list, or any particular order, I'm assuming I can't just put it anywhere in the startup.txt list...

I'm thinking it would be done like
Correct or does it matter?

I don't know but I think rel_path=blahblah needs to be PART of the set cmdline line before the "physkeyboard=rhod400" string... or does it not matter (someone once told me it mattered).

[Gremlin75]

Originally Posted by ndno

Hmmmm... I ignored the pop up window querying for the driver (I had the same CDC ACM message like you did). Instead I manually went to the Device Manager and use the instructions I decribed above to install it.

Did you try arrrghhh's pdanet install trick?

I hadn't...but I went back to his post and downloaded it. After installing it, I was able to connect to the phone and use MyPhoneExplorer to sync my Outlook calendar & contacts to the phone. Woo hoo!

I'm still getting the error messages about the CDC messages, and I've tried pointing the phone to both the USB Drivers directory as well as the PDANet directory. Can't locate drivers in either location. Seems to work just fine without them however.

Thanks for the help! Would definitely recommend this solution to anyone running Android and trying to sync to Outlook.

I'd like to post a thread to provide instructions and links to the required files...crediting you & arrrghhh, of course. Do I have your permission to do so?

[Recursion]

Originally Posted by arrrghhh

Heh, I'll add that to the FAQ. Not many people have a SIM installed if they use CDMA .
I'm trying to keep the first post as clean as possible - the more text I put in there, the less people are going to want to read it...

Actually, Sprint TP2s came with SIM cards pre-installed right out of the box. I don't know if Verizon & other TP2s did. Anyhow, I just wedged a piece of paper between the SIM Card and my phone's contacts & re-inserted the SIM. I lose too much chit.

[n1nj4Lo]

Trying it now with everything directly on the card, no folders or anything... I also remembered to revert the startup.txt back to its original form.

Man I hope this works!!!