NAND Testing - 05-25 Update: New LK, Recovery.img, Kernel Updates through Recovery - Page 132

**arrrghhh** · #**1311** (**permalink**) 02-21-2011, 03:49 PM

Quote:

Originally Posted by Lmiller1708

Just was checking. Didn't know if there was different versions out there or not. Sounds like it might be the bad blocks...

oic. When you task 28 or task 29 thru mtty, no bad blocks show?

**Lmiller1708** · #**1312** (**permalink**) 02-21-2011, 04:07 PM

Wirelessly posted (Vogue: Mozilla/5.0 (Linux; U; Android 2.2.1; en-us; MSM Build/FRX04) AppleWebKit/533.1 (KHTML, like Gecko) Version/4.0 Mobile Safari/533.1)

Quote:

Originally Posted by arrrghhh

Quote:

Originally Posted by Lmiller1708

Just was checking. Didn't know if there was different versions out there or not. Sounds like it might be the bad blocks...

oic. When you task 28 or task 29 thru mtty, no bad blocks show?

I have not tried it yet... I will try to later...

**natemcnutty** · #**1313** (**permalink**) 02-21-2011, 04:42 PM

Quote:

Originally Posted by arrrghhh

oic. When you task 28 or task 29 thru mtty, no bad blocks show?

Arrrghhh, can you do a task 32, then a task 37 and post the results?

**arrrghhh** · #**1314** (**permalink**) 02-21-2011, 05:35 PM

Quote:

Originally Posted by natemcnutty

Arrrghhh, can you do a task 32, then a task 37 and post the results?

Hrm. Never used these commands before... I went to bootloader, plugged in, launch mtty... Then I did the

Code:

set 14 0

command, followed by task32 and task37. task32 gave me an error, and task37 just hung. Output:

Code:

Cmd>set 14 0
HTCST   ÚÈÒHTCE
Cmd>task 32
No card inserted

Level = 0

Cmd>task 37


Buffer = 0x85340000, Size = 0xFFFE8

Nothing else... Not sure if I shouldn't have done that set 14 0 command or not. I'll try it again without...

Edit - same result without the set 14 0.

Ok, realized that the task 32 command needed an SD inserted...

Code:

Cmd>task 32
Card inserted

SD clk rate 19MHz

Cmd5 CMD_TIMEOUT
SD clk rate 144KHZ

SD 2.0 HC card 
TURBO mode : SD Clk rate 24 MHz

SD Init OK

Card inserted

SD clk rate 19MHz

Cmd5 CMD_TIMEOUT
SD clk rate 144KHZ

SD 2.0 HC card 
TURBO mode : SD Clk rate 24 MHz

SD Init OK

Level = 0

Still freezes on task 37 after that "Buffer = " output...

**natemcnutty** · #**1315** (**permalink**) 02-21-2011, 06:41 PM

Quote:

Originally Posted by arrrghhh

Hrm. Never used these commands before... I went to bootloader, plugged in, launch mtty... Then I did the

Code:

set 14 0

command, followed by task32 and task37. task32 gave me an error, and task37 just hung. Output:

Code:

Cmd>set 14 0
HTCST   ÚÈÒHTCE
Cmd>task 32
No card inserted

Level = 0

Cmd>task 37


Buffer = 0x85340000, Size = 0xFFFE8

Nothing else... Not sure if I shouldn't have done that set 14 0 command or not. I'll try it again without...

Edit - same result without the set 14 0.

Ok, realized that the task 32 command needed an SD inserted...

Code:

Cmd>task 32
Card inserted

SD clk rate 19MHz

Cmd5 CMD_TIMEOUT
SD clk rate 144KHZ

SD 2.0 HC card 
TURBO mode : SD Clk rate 24 MHz

SD Init OK

Card inserted

SD clk rate 19MHz

Cmd5 CMD_TIMEOUT
SD clk rate 144KHZ

SD 2.0 HC card 
TURBO mode : SD Clk rate 24 MHz

SD Init OK

Level = 0

Still freezes on task 37 after that "Buffer = " output...

Bummer, must not work on our devices. Doesn't work on the Raph's either. Task 32 is supposed to prep things, then task 37 dumps the KITL log.

**arrrghhh** · #**1316** (**permalink**) 02-21-2011, 07:23 PM

Quote:

Originally Posted by natemcnutty

Bummer, must not work on our devices. Doesn't work on the Raph's either. Task 32 is supposed to prep things, then task 37 dumps the KITL log.

Bummer indeed.

Let me know if you want me to try anything else... mtty was surprisingly easy

.

**natemcnutty** · #**1317** (**permalink**) 02-21-2011, 07:44 PM

Quote:

Originally Posted by arrrghhh

Bummer indeed.

Let me know if you want me to try anything else... mtty was surprisingly easy

.

You work with putty all day. It's basically putty to your phone instead of a router :P

I wish I knew more, but the details aren't very public on mtty.

**arrrghhh** · #**1318** (**permalink**) 02-21-2011, 07:51 PM

Quote:

Originally Posted by natemcnutty

You work with putty all day. It's basically putty to your phone instead of a router :P

I wish I knew more, but the details aren't very public on mtty.

Yea, details on mtty seem very scant... disappointing, at best.

I keep second guessing my steps, but since I can flash that old nbh with that different partition table, I can't help but think there is something wrong with the new table... just baffled that acl and lmiller don't have issues...

**natemcnutty** · #**1319** (**permalink**) 02-21-2011, 07:54 PM

Quote:

Originally Posted by arrrghhh

Yea, details on mtty seem very scant... disappointing, at best.

I keep second guessing my steps, but since I can flash that old nbh with that different partition table, I can't help but think there is something wrong with the new table... just baffled that acl and lmiller don't have issues...

Right now, I'm taking the old NBH and hex editing and flashing. Seeing if any of my changes to the table fix/break it.

**arrrghhh** · #**1320** (**permalink**) 02-21-2011, 08:03 PM

Quote:

Originally Posted by natemcnutty

Right now, I'm taking the old NBH and hex editing and flashing. Seeing if any of my changes to the table fix/break it.

Sounds good man. Keep us posted

.