nueLED - configure/customize your LEDs... - Page 20

jamal33 · #**191** (**permalink**) 03-26-2008, 01:07 PM

Question... I managed to get the blue tooth light to blink instead of my original green led but however its on the opposite side. (near the little envelope button) i thought it would blink where the original green led did. any help?

Radar · #**192** (**permalink**) 03-26-2008, 01:15 PM

that led is physically in that spot...

enormous · #**193** (**permalink**) 03-26-2008, 01:24 PM

I've got a reproducible "problem". In nueLED, I have the charging LED (Addr 22, Mode 1) set to disabled. If the screen is on when I plug the charger in, the LED is in fact disabled. If I turn off the screen though, the orange charging light comes back on. Turning on the screen again does not change this. If I enter nueLED and do a Extra->Reset LEDs, the charging light goes off... until the screen turns off and it turns back on.

I have reproduced this using multiple flashes of various versions of multiple ROMs.

I've searched the thread, and have only found one similar report to this. Let me know if I can be of further assistance in tracking this down.

jamal33 · #**194** (**permalink**) 03-26-2008, 01:29 PM

Thanks Radar...

But when my battery is low the red light comes on where the original is and so does orange. so i figured why not blue.

ok so I got my signal led to blink blue (near the little envelope) can i also add something to the other led so that it can blink as well? (near the "e")

Thanks,

kraygh · #**195** (**permalink**) 03-26-2008, 01:41 PM

Quote:

Originally Posted by jamal33

Thanks Radar...

But when my battery is low the red light comes on where the original is and so does orange. so i figured why not blue.

ok so I got my signal led to blink blue (near the little envelope) can i also add something to the other led so that it can blink as well? (near the "e")

Thanks,

Many are making the same assumption you are when first getting the program. NueLED does NOT directly control LEDs.
It redirects their addresses so you can swap one existing function with another.
This means you will not be able to get any color you want (purple) or make it flash faster or both at the same time.
Although I bet NueLED2 will have something along those lines. (No2Chem: Just making sure this makes your top 30 to-do list.

jamal33 · #**196** (**permalink**) 03-26-2008, 01:56 PM

Kraygh thanks for a better understanding. I will be looking out for this nice app.

cjrusso1 · #**197** (**permalink**) 03-26-2008, 01:58 PM

so has anyone found the address for the red led? i cant seem to find in and i red through all the posts

idenkilla · #**198** (**permalink**) 03-26-2008, 02:05 PM

i found address 4 mode 4 but its not constantly flashing for some reason

cjrusso1 · #**199** (**permalink**) 03-26-2008, 02:17 PM

Quote:

Originally Posted by idenkilla

i found address 4 mode 4 but its not constantly flashing for some reason

yeah i tried it .. also tried it to set to notification .. soft reset and no red...

also idk if this has been addressed but when u go into comm manager and turn on bluetooth it resets the leds... well on mine at least - JUST TESTED AGAIN and it happened again .. is there a fix?

- my set up is blue service, green bluetooth , orange notification

cjrusso1 · #**200** (**permalink**) 03-26-2008, 02:42 PM

also to no2chem there is a program floating around from the bb8100

http://www.geekandproud.net/blackber...colorpearl.zip

here is the thread

http://blackberryforums.pinstack.com...e_options.html

is there a way of mayb going into it and being able to pull the hex codes

or mayb a way to rewrite the program a lil to have 000000 codes