Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

I just donated and say thanks again for all the efforts No2Chem!

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

Which advanced settings? Where are they located? Thanks.


EDIT: Nevermind, found it

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

from 5051 a folder gets installed under "Programs" call "Advanced settings" and in that folder their is an icon named "EPST config"

good luck

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

I haven't ordered mine yet. Running a 2GB card. Good luck.

rw

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

I don't use s2u2 and still have the answer issues. Also it is the DATA connection not just evdo. If the phone is using data it has to switch to phone mode and this is taking forever which is causing the problem.

I tested this by purposly using data then closing all programs and calling myself from a landline. It takes forever to answer the call. I called again right after the first phone call and it answered immediatly. We just need the timeout from data to phone mode to be like 5-10 seconds instead of whatever it is. It seems like there is no timeout so it stays in data mode.

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

Yeah, I am not using S2U either, so this isn't my issue.

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

anyone gotten gpsgate to work yet?

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

GBM85,

when I look at the comm manager, it also shows a constant connect on the data icon, is that also a bug? The Microsoft Direct Push icon is also lit up. Is this normal since I'm using exchange as my messaging setup?

RW

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

i have the mogul big button dialer and it doesnt show that my EVDO is always on if anyone wants it ill post it up here for you.this is the one where the ## codes work.

Re: No2Chem nueROM 2.0 (WM6.1) Thread
 

Okay. This is what I have found so far concerning the data connection:

Setup 1 - using Microsoft Direct Push (MDP) and Data Connection

I check comm manager and notice that both the data connection and Microsoft Direct Push are lit up and showing as running additionally, the arrows in the taskbar are showing a connection. I disable MDP and the data connection continues to run. Data connection will shut down if I press the icon within comm manager. Icon returns back to tower on taskbar.

Setup 2 - Using Active Sync and Data Connection

I check the comm manager, no data connection enabled, no active sync enabled. I click on active sync and initiate a sync to my server. Data Connection lights up and arrows light up in task bar. Active sync finishes but connection manager icon still shows on and connection arrows on taskbar stay on.

Using Itsall_cool regedits on a previous post, I disconnected the data connection. I then set active sync to check for mail every five minutes. The data connection begins but after five minutes does not shut down (it normally takes about 20 seconds to check and download). The data arrows on the taskbar continue to show as well. Data arrows continue to show until I manually shutdown the connection. Icon changed from arrows to antenna tower after I manually shut the data connection. If I run active sync manually the data connection also continues to run after it has finished sync'ing.

Moved over to Pocket Internet Explorer (PIE).

Initiated an Internet Connection to MSN Mobile (dialer showed calling 777) and ran great. Data arrows showed up. Shutdown PIE but arrows remained. Checked out Task Manager and PIE is not loaded. Data arrows continue to show until I manually shutdown the connection. Icon changed from arrows to antenna tower after I manually shut the data connection.

From what I have found it seems that the data connection is continueously running when you establish either an MDP, Active Sync (manual or scheduled), or Web connection. You have to manually disconnect the vision data connection.

RW