rstoyguy's 19208 Rom & Kitchen Basekit v1.0801 Updated 8/01/08 - Page 7

mtb29er · #61 (**permalink**) 07-30-2008, 01:01 PM

Quote:

Originally Posted by rstoyguy

NO!!! Well, ok.

Change the following reg key

HKCU\software\A_C\S2U2
"S2UText"="rstoyguy"

You the man thanks. .

Vancer · #62 (**permalink**) 07-30-2008, 07:03 PM

Hey rstoyguy it's Vancer .... again... hehe

As you know i've been cooking (as you have helped me in OMJ's thread) and i use the same base kitchen as you but have been working off of OMJ's generic clean rom. I have read through here and a couple ppl have asked, but i still haven't seen a clear cut answer on a few questions.

1. Getting rid of the cube alltogether? Since I'm using OMJ's generic clean, do you know what files need to be deleted after running prepit.bat? I figure you know how to do this b/c I'm assuming you had to do it to add your s3 OEM. I'm pretty sure his generic would require the same deletions as the stock sprint as I believe he simply replaced the sprint .brns with generic ones but left the cube in.

2. Since i was modding the cube pre-cubeconfig by thisguyinoc, I'm familiar with aplauncher, mediahubmini, etc.. but don't know all the files to be deleted or out of which directory (such as \sys or \oem\oemapps) in oder to say goodbye to that cube and free up some memory?

3. Once I figure out what files to delete, will buildOS take care of writing the .rgu correctly since the files will not be there?

4. If successful at getting the cube deleted, what do I need to leave in so I will still have touchflo and have finger scrolling for all my apps?

5. Also (if successful at deleting the cube), I assume quickdial.exe would be one of the deletions, but would i need to leave it in for the quick contacts in HHC to function properly (or even would they w/o the cube)? Or if I used something else like spb mobile shell would it have it's own .exe to launch quick dialing of contacts? (or does it use quickdial.exe)

6. I also have the same questions about what to delete after prepit.bat in order to get rid of the letter recognizer and block recognizer? (I actually use the touch keypad and full qwerty)

Much appreciated!!

For the guy asking earlier, I have sucessfully just deleted all three transcriber directories out of \sys and it indeed removes it from the install w/o any problems. I guess buildOS recognized that and took care of the .rgu itself as I'm hoping it will do for the letter and block recognizer once I figure out what to delete.

**rstoyguy** · #63 (**permalink**) 07-30-2008, 07:23 PM

Quote:

Originally Posted by Vancer

Hey rstoyguy it's Vancer .... again... hehe

As you know i've been cooking (as you have helped me in OMJ's thread) and i use the same base kitchen as you but have been working off of OMJ's generic clean rom. I have read through here and a couple ppl have asked, but i still haven't seen a clear cut answer on a few questions.

1. Getting rid of the cube alltogether? Since I'm using OMJ's generic clean, do you know what files need to be deleted after running prepit.bat? I figure you know how to do this b/c I'm assuming you had to do it to add your s3 OEM. I'm pretty sure his generic would require the same deletions as the stock sprint as I believe he simply replaced the sprint .brns with generic ones but left the cube in.

2. Since i was modding the cube pre-cubeconfig by thisguyinoc, I'm familiar with aplauncher, mediahubmini, etc.. but don't know all the files to be deleted or out of which directory (such as \sys or \oem\oemapps) in oder to say goodbye to that cube and free up some memory?

3. Once I figure out what files to delete, will buildOS take care of writing the .rgu correctly since the files will not be there?

4. If successful at getting the cube deleted, what do I need to leave in so I will still have touchflo and have finger scrolling for all my apps?

5. Also (if successful at deleting the cube), I assume quickdial.exe would be one of the deletions, but would i need to leave it in for the quick contacts in HHC to function properly (or even would they w/o the cube)? Or if I used something else like spb mobile shell would it have it's own .exe to launch quick dialing of contacts? (or does it use quickdial.exe)

6. I also have the same questions about what to delete after prepit.bat in order to get rid of the letter recognizer and block recognizer? (I actually use the touch keypad and full qwerty)

Much appreciated!!

For the guy asking earlier, I have sucessfully just deleted all three transcriber directories out of \sys and it indeed removes it from the install w/o any problems. I guess buildOS recognized that and took care of the .rgu itself as I'm hoping it will do for the letter and block recognizer once I figure out what to delete.

1,2,4: The way to do it is to add the S3 Cube to ..\OEM then run buildos. Everytime it comes up with a duplicate, delete the file out of ..\OEMAPPS. Repeat until you do not get the duplicate files anymore, then delete S3 Cube out of the ..\OEM directory....CUBE is GONE! Touchflo remains...

3: The RGU will have a few "orphaned" registry entries, I'm not sure it will save you that much space, but you could delete them...

5: I don't use hhc home, but I would assume you would have to leave quickdial in there. Spb shell I'm sure has it's own way, but one file won't hurt much of anything.

6: I just tried it, and my guess worked! I managed to kill the Block & Letter recognizer from my keyboard list.

Try the following in an OEM:

Quote:

[-HKEY_CLASSES_ROOT\CLSID\{42429690-ae04-11d0-a4f8-00aa00a749b9}]

See the "-" immediately after the bracket? That should tell BuildOs to kill that whole registry key...That should kill the Letter recognizer. Try the same on the others you want gone as well...

And let me know if buildos supports that, and if it worked for ya! I may want to use that for me-self!

Vancer · #64 (**permalink**) 07-30-2008, 08:09 PM

Quote:

Originally Posted by rstoyguy

1,2,4: The way to do it is to add the S3 Cube to ..\OEM then run buildos. Everytime it comes up with a duplicate, delete the file out of ..\OEMAPPS. Repeat until you do not get the duplicate files anymore, then delete S3 Cube out of the ..\OEM directory....CUBE is GONE! Touchflo remains...

3: The RGU will have a few "orphaned" registry entries, I'm not sure it will save you that much space, but you could delete them...

5: I don't use hhc home, but I would assume you would have to leave quickdial in there. Spb shell I'm sure has it's own way, but one file won't hurt much of anything.

6: I just tried it, and my guess worked! I managed to kill the Block & Letter recognizer from my keyboard list.

Try the following in an OEM:

See the "-" immediately after the bracket? That should tell BuildOs to kill that whole registry key...That should kill the Letter recognizer. Try the same on the others you want gone as well...

And let me know if buildos supports that, and if it worked for ya! I may want to use that for me-self!

Thanks!!! That's a great idea with the buildOS trick

I'm sure it will take a while but it will get the job done!

On the block and letter thing...
I just edited the key,
HKCR\CLSID\{4242961...block }\IsSIPInputMethod...changed default from 1 to 0,
Same edit for {4242960...letter } and both are gone from optional keyboards

That didn't do anything for the actual files still being there of course but at least I don't have to see those options anymore. I will just add that to the .rgu of my optional regedits in \sys and and that should take care of it rather than trying to kill that reg entry correct?

motorcitymadman · #65 (**permalink**) 07-30-2008, 10:51 PM

Quick question. In addition to your rom, I'm running Spb Mobile Shell. The Mobile Shell plug-in sits in a locked position at the top of the home screen. The digital clock is second. Is there a way to unlock the Mobile Shell plug-in so that I can move the digital clock up and have the Mobile Shell plug-in rest under the digital clock plug-in?

motorcitymadman · #66 (**permalink**) 07-30-2008, 11:03 PM

Disregard the last post. I found the answer I was looking for. HKLM > SOFTWARE > Microsoft > Today > Items > Spb Mobile Shell > Type. Change Type from '5' to '4' and it will show up as an Moveable plugin. Search does wonders!!!!!

Vancer · #67 (**permalink**) 07-30-2008, 11:05 PM

rstoyguy,

I tried that method and it didn't work

Got rid of all the duplicates and ran buildos which completed successfully but after i flashed and booted up i found a problem. Everything seemed fine until i swiped my finger upward as if to launch the cube and the screen went a little dimmer and the phone locked up. I'm guessing it has something to do with that gesture in the touchflo reg settings somewhere calling for something to launch and it's no longer there. Any help???

**rstoyguy** · #68 (**permalink**) 07-30-2008, 11:27 PM

Quote:

Originally Posted by Vancer

rstoyguy,

I tried that method and it didn't work

Got rid of all the duplicates and ran buildos which completed successfully but after i flashed and booted up i found a problem. Everything seemed fine until i swiped my finger upward as if to launch the cube and the screen went a little dimmer and the phone locked up. I'm guessing it has something to do with that gesture in the touchflo reg settings somewhere calling for something to launch and it's no longer there. Any help???

Search for the regedit to disable the cube.