Trying to load hard spl

pavetim · #1 (**permalink**) 05-20-2008, 08:02 AM

Whats up with the ROM loading? I go to load hard spl on my tilt and when it gets to the part where it should be tri-color screen the screen is just plain white, and it disconnects from my PC and I have to pull the battery to reset it? Whats going on here guys?

**Certs** · #2 (**permalink**) 05-20-2008, 08:21 AM

There is a small dialog on your phones screen asking you if its OK to run the program to enter bootloader. Make sure you see this and hit OK.

pavetim · #3 (**permalink**) 05-20-2008, 08:34 PM

i did taht and it just goes to white screen. I did some jumpspl on xda-dev and it did what it said but then it went to load and it had some error. How is it so easy with ppl with the same phone.

pavetim · #4 (**permalink**) 05-20-2008, 11:22 PM

Ok I got it loaded but how would i make positve that it is loaded? I said it went through but before I flash i want to make sure. And after I flash hardspl do I have to keep the file on the phone

Mark43 · #5 (**permalink**) 05-21-2008, 12:24 AM

Quote:

Originally Posted by pavetim

Ok I got it loaded but how would i make positve that it is loaded? I said it went through but before I flash i want to make sure. And after I flash hardspl do I have to keep the file on the phone

You need to remove your sd card from the phone and enter the bootloader screen (tri-color screen) to do this hold down the power and camera button and put the stylis in the reset hole like you would to perform a soft rest. Keep holding the power and camera buttons until you see the tri-color screen (usually 1-2 seconds). Then up top you should see what spl you have loaded i.e. mine says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8

Note: You only need to flash hardSPL once and you are good to flash any ROM you want. JumpSPL is only needed for hardSPL not for flashing ROM's

After you hardSPL your device, I found the best way to flash is from the sd card. To do this place the .nbh you want to flash on the root of the sd card and rename it "KAISIMG.nbh" without quotes. Make sure the card is in the phone and enter the tri-color screen by the method above. After you do that follow the on screen instructions and soft reset once it says it is completed.

Ron

pavetim · #6 (**permalink**) 05-21-2008, 12:43 AM

Ok sounds good I did all that and went to flash from my sd card it went to tri color screen, I hit the power button to start flash and it did nothing. Maybe I didn't put the file on the root of the card what does that mean, root? I downloaded on my PC dragged to my computer where it said SD card, and put in password. Is all this right cause it isn't working.

pavetim · #7 (**permalink**) 05-21-2008, 06:03 AM

Ok I got it now I didnt have my card formatted in FAT32 ok thanks though.

zubrien · #8 (**permalink**) 12-01-2009, 10:40 PM

i am trying to laod the hard spl 1.0 from xda-dev, every time i try my screen turns white like this guy was explaining, anyone know why, would appeciate it as i am trying to unlock it

sadc · #9 (**permalink**) 09-03-2011, 01:38 PM

Hi everyone.
From nowhere my tytn stoped working and has a three colour screen wich says:
KAIS1*0 MFG
SPL-1.0.OliP0f
CPLD-8
I tried to reset and hard reset but nothing works! what should I do???
What file should I have to put and where? Please help!