PPCGeeks Forums HTC Arrive HTC HD2 HTC Thunderbolt HTC Touch Pro 2 HTC Evo 4G HTC Evo 3D Samsung Galaxy S II Motorola Droid X Apple iPhone Blackberry
Go Back   PPCGeeks > Windows Mobile > General Windows Mobile Discussions > Legacy WM Devices > HTC Kaiser

Notices



Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 05-20-2008, 08:02 AM
pavetim's Avatar
Lurker
Offline
Pocket PC: 8925
 
Join Date: May 2008
Posts: 9
Reputation: 0
pavetim is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Trying to load hard spl

Whats up with the ROM loading? I go to load hard spl on my tilt and when it gets to the part where it should be tri-color screen the screen is just plain white, and it disconnects from my PC and I have to pull the battery to reset it? Whats going on here guys?
Reply With Quote
  #2 (permalink)  
Old 05-20-2008, 08:21 AM
Certs's Avatar
Retired Staff
Offline
Pocket PC: iPhone4
Carrier: AT&T
Location: Maspeth. NY
 
Join Date: Oct 2006
Posts: 1,694
Reputation: 1866
Certs is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on repCerts is halfway to VIP status based on rep
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

There is a small dialog on your phones screen asking you if its OK to run the program to enter bootloader. Make sure you see this and hit OK.
__________________
Reply With Quote
  #3 (permalink)  
Old 05-20-2008, 08:34 PM
pavetim's Avatar
Lurker
Offline
Pocket PC: 8925
Threadstarter
 
Join Date: May 2008
Posts: 9
Reputation: 0
pavetim is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

i did taht and it just goes to white screen. I did some jumpspl on xda-dev and it did what it said but then it went to load and it had some error. How is it so easy with ppl with the same phone.
Reply With Quote
  #4 (permalink)  
Old 05-20-2008, 11:22 PM
pavetim's Avatar
Lurker
Offline
Pocket PC: 8925
Threadstarter
 
Join Date: May 2008
Posts: 9
Reputation: 0
pavetim is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

Ok I got it loaded but how would i make positve that it is loaded? I said it went through but before I flash i want to make sure. And after I flash hardspl do I have to keep the file on the phone

Last edited by pavetim; 05-20-2008 at 11:41 PM.
Reply With Quote
  #5 (permalink)  
Old 05-21-2008, 12:24 AM
Mark43's Avatar
Lurker
Offline
Pocket PC: AT&T Tilt 8925
Carrier: AT&T
Location: Yakima, WA
 
Join Date: Mar 2008
Posts: 16
Reputation: 0
Mark43 is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

Quote:
Originally Posted by pavetim View Post
Ok I got it loaded but how would i make positve that it is loaded? I said it went through but before I flash i want to make sure. And after I flash hardspl do I have to keep the file on the phone
You need to remove your sd card from the phone and enter the bootloader screen (tri-color screen) to do this hold down the power and camera button and put the stylis in the reset hole like you would to perform a soft rest. Keep holding the power and camera buttons until you see the tri-color screen (usually 1-2 seconds). Then up top you should see what spl you have loaded i.e. mine says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8

Note: You only need to flash hardSPL once and you are good to flash any ROM you want. JumpSPL is only needed for hardSPL not for flashing ROM's

After you hardSPL your device, I found the best way to flash is from the sd card. To do this place the .nbh you want to flash on the root of the sd card and rename it "KAISIMG.nbh" without quotes. Make sure the card is in the phone and enter the tri-color screen by the method above. After you do that follow the on screen instructions and soft reset once it says it is completed.

Ron
__________________
AT&T Tilt - In Washington State USA
ROM - [Apr 01 Updated] Dutty's WM6.1 Hybrid UC RTM
Radio - 1.58.21.23
SPL - Hard-SPL v1

Last edited by Mark43; 05-21-2008 at 12:28 AM. Reason: added info on jumpSPL
Reply With Quote
  #6 (permalink)  
Old 05-21-2008, 12:43 AM
pavetim's Avatar
Lurker
Offline
Pocket PC: 8925
Threadstarter
 
Join Date: May 2008
Posts: 9
Reputation: 0
pavetim is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

Ok sounds good I did all that and went to flash from my sd card it went to tri color screen, I hit the power button to start flash and it did nothing. Maybe I didn't put the file on the root of the card what does that mean, root? I downloaded on my PC dragged to my computer where it said SD card, and put in password. Is all this right cause it isn't working.
Reply With Quote
  #7 (permalink)  
Old 05-21-2008, 06:03 AM
pavetim's Avatar
Lurker
Offline
Pocket PC: 8925
Threadstarter
 
Join Date: May 2008
Posts: 9
Reputation: 0
pavetim is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

Ok I got it now I didnt have my card formatted in FAT32 ok thanks though.
Reply With Quote
  #8 (permalink)  
Old 12-01-2009, 09:40 PM
zubrien's Avatar
Lurker
Offline
Pocket PC: htc 8925
Carrier: boost mobile
 
Join Date: Dec 2009
Posts: 3
Reputation: 0
zubrien is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

i am trying to laod the hard spl 1.0 from xda-dev, every time i try my screen turns white like this guy was explaining, anyone know why, would appeciate it as i am trying to unlock it
Reply With Quote
  #9 (permalink)  
Old 09-03-2011, 01:38 PM
sadc's Avatar
Lurker
Offline
Pocket PC: htc tytn ii
Carrier: vodafone
 
Join Date: Sep 2011
Posts: 3
Reputation: 0
sadc is a n00b
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Re: Trying to load hard spl

Hi everyone.
From nowhere my tytn stoped working and has a three colour screen wich says:
KAIS1*0 MFG
SPL-1.0.OliP0f
CPLD-8
I tried to reset and hard reset but nothing works! what should I do???
What file should I have to put and where? Please help!
Reply With Quote
Reply

  PPCGeeks > Windows Mobile > General Windows Mobile Discussions > Legacy WM Devices > HTC Kaiser

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -4. The time now is 06:37 PM.


Powered by vBulletin® ©2000 - 2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.0
©2012 - PPCGeeks.com