SPC/MSL code of sprint diamond

[clockcycle]

Originally Posted by land2634

Also, I am now noticing that when I go to Start-Settings-System-Device Information the MEID field is completely blank. I am completely baffled now, as I have not even so much as flashed a ROM to the device since activating it, and the MEID showed just last night when I looked there.

Those errors are not uncommon, I have seen it before, just loook again, or soft reset and look again. It means it is having a hard time reading the information in the alloted time and times out, giving you an error.

If it persists, I suggest a Hard Reset, if it continues, talk to tech or store for a possible exchange.

-CC

[clockcycle]

Originally Posted by blee0125

For Sprint Diamonds

Use CDMA Workshop and connect to the phone in diag mode.
Go to the "Security" Tab and hit "Read" SPC.
Select Universal Ram Method and Custom.
Address is: 018E:0190
Hit READ to find your SPC.

For Telus Diamonds I was told GetSPC works if you convert MEID to p-ESN but I haven't tried it myself.

On my Sprint Diamond I used the pESN and the code getspc gave didn't work and it's the same as the one Sprint gave me for manual activation online.

-CC

[Mr. X]

Originally Posted by blee0125

For Sprint Diamonds

Use CDMA Workshop and connect to the phone in diag mode.
Go to the "Security" Tab and hit "Read" SPC.
Select Universal Ram Method and Custom.
Address is: 018E:0190
Hit READ to find your SPC.

For Telus Diamonds I was told GetSPC works if you convert MEID to p-ESN but I haven't tried it myself.

thats correct.

the telus device actually has a ESN and MEID. ESN is not shown unless you goin to EPST or into Qpst

[Mr. X]

Originally Posted by clockcycle

On my Sprint Diamond I used the pESN and the code getspc gave didn't work and it's the same as the one Sprint gave me for manual activation online.

-CC

i think sprint may have the one time use ticker attached to there SPC.

once yo use it once you cannot use it again it shuts it off in the Service programming.

if you use QPST and check service programming (if you can get in with spc) you can see the "one time use" setting in there.

[land2634]

Originally Posted by blee0125

For Sprint Diamonds

Use CDMA Workshop and connect to the phone in diag mode.
Go to the "Security" Tab and hit "Read" SPC.
Select Universal Ram Method and Custom.
Address is: 018E:0190
Hit READ to find your SPC.

For Telus Diamonds I was told GetSPC works if you convert MEID to p-ESN but I haven't tried it myself.

I will try this as soon as I get off of work. I'm not familiar with CDMA Workshop or diagnostic mode. Where do I get the workshop and how do I go into diagnostic mode? Thanks!

[cornelious2]

just call and ask sprint for your msl. i have used mine more than once that they gave me. just mention that you had to activate your phone a second/third time after hard reseting and you want to just write down the info and put it back in if it gets wiped again.

[tobeychris]

Originally Posted by tq0aezm

can u give me the cmda workshop?
my email zzh0903@163.com.
or tell me where can down cdma workshop

No, that's illegal. You can pay for the software, or ask your question somewhere else. The cost of the full program is $99 I believe.

As for the MEID I saw that was posted a while ago... at one point the telus roms (and old kitchen) actually set the MEID display to all zeros. If this it what you say, I wouldn't be worried. I believe the newest version of the kitchen, which most chefs are using show most setting including HEX ESN, network username, Hex MEID, MDN and MSID.

I'm pretty sure I put them in the kitchen... if not (can't look at the moment) they should be in the next release.

[jhgas]

Originally Posted by blee0125

For Sprint Diamonds

Use CDMA Workshop and connect to the phone in diag mode.
Go to the "Security" Tab and hit "Read" SPC.
Select Universal Ram Method and Custom.
Address is: 018E:0190
Hit READ to find your SPC.

For Telus Diamonds I was told GetSPC works if you convert MEID to p-ESN but I haven't tried it myself.

Thanks a lot. I was finally able to do this, I even changed it to all 0´s so I wouldn´t need to remember them.

[luay78]

. Find your ESN in hex. If you have it in decimal, use this to convert it. You want the Pseudo ESN Hex number.

2. Download PPST_KeyGen.dll and GetSPC.exe, and then transfer them to your phone.

3. Run GetSPC.exe on your phone.

4. Enter your hex ESN in the Input field.

5. Press Go.

6. Write down your SPC from the Output field.

NOT WORKED WITH ME

DIAMOND SPRINT

guys i couldnt get my correct SPL/MSL code to edite the EPST . here is the details who can help me and how i can do it by my self..
MEID Hex


A10000055186B4MEID Dec270113178105342900Pseudo ESN Hex8022F2EAPseudo ESN Dec12802290410REAL Binary10100001000000000000000000000101010100011000 011010110100

[sequan]

I also have a sprint diamond.

the exe did not work for me.

I had to use the registry hack to get it.

that is the only thing that worked.......