Unified ROM 1.0.0.43 RC4 PUBLIC BETA (Updated 4/4/2007) - Page 16

jambaj0e · #**151** (**permalink**) 04-22-2007, 06:52 AM

Doesn't matter how long I wait. Bluetooth doesn't come on if I try to turn it on again. I still have to reset it.

**luv2chill** · #**152** (**permalink**) 04-22-2007, 01:02 PM

OK, hopefully some other people can try this and corroborate. What apps (if any) do you have installed that involve bluetooth?

tbhausen · #**153** (**permalink**) 04-22-2007, 01:53 PM

luv2chill, I've seen that BT toggle issue a couple times, too. I was blaming GpsGate, but I've confirmed it's not a factor. Minor annoyance.

Todd/Indy

jambaj0e · #**154** (**permalink**) 04-22-2007, 02:10 PM

I just did a fresh install, and the only apps that I use w/ Bluetooth are winmobileapps phone profile, Voice Command, and iGuidance. I am using my Samsung WEP200 bluetooth headset and a Holux GPSlim 256 bluetooth GPS unit.

swimmrguy · #**155** (**permalink**) 04-22-2007, 08:08 PM

Quote:

Originally Posted by 2ndchance

Ok... I must be stupid, but I don't know how to install this new ROM....

Can someone please point me in the right direction? I am currently using Sprint's latest Rom.

You can find an installer for this (and other ROMs) in this thread...it worked fine for me.

http://www.ppcgeeks.com/custom-rom-i...you-t2847.html

psychotic · #**156** (**permalink**) 04-22-2007, 11:00 PM

I tried customizing this Rom using the sprint clean and simple installer, along with this thread:
http://ppcgeeks.com/how-to-remove-fa...hods-t360.html

on how to access the extended rom and reinstall 'junk' cabs so they can later be removed... however I am not seeing anything in the extended rom directory after unlocking it, and I am not getting the 3 sec countdown before extended rom kicks in, so I cannot use the hard reset method. Am I missing something?

gbm85 · #**157** (**permalink**) 04-23-2007, 12:15 AM

Kirvin's 3.5 for Sprint comes with a blank extended ROM which you flashed to your phone when you used that installer. You will have to reflash the official Sprint extended ROM.

psychotic · #**158** (**permalink**) 04-23-2007, 01:00 AM

the original sprint installer is a .exe file.... how do i get the other files in order to replace the nbf file with this one??

**luv2chill** · #**159** (**permalink**) 04-23-2007, 02:36 AM

Quote:

Originally Posted by psychotic

the original sprint installer is a .exe file.... how do i get the other files in order to replace the nbf file with this one??

Extract it with winrar.

2ndchance · #**160** (**permalink**) 04-23-2007, 02:53 AM

I wished I wasn't so impatient and waited to read the replies before I attemped this... so this is where I'm at.

I downloaded the last ROM from sprints web site. Following tbhausen's post, I extracted it using WinRAR. I copied the new nk.nbf over and overwritten the original.

I ran the RomUpgradeUT.ext and the installation went smoothly. I got the apache boot screen, halted the auto configuration, and all looked good.

I installed Total commander and ran only the required CABS.

Everything seems to be functioning fine. I was able to reinstall all of my programs. I have only run into a couple of issues and I hope you all can help me.

1. Total Commander. I accessed /Extended_Rom/ and see the cab files there. There are some junk ones that I don't want so, through total commander, I deleted them. After a soft reset, they reappear in the Extended Rom? What's up with that?

2. I installed this ROM because an earlier post said that DUN via Bluetooth (or PAN) is working. I can't get it to work. I searched this forum and also PDAPhoneHome.Com, and can't find directions to do this.

Can someone point me to the right place, or better yet, post instructions on this topic.

I would really appreciate some help. Thanks in advance.