[TOOL] Task 29 (format internal Memory) without drivers, witout mtty

[Deltatristar500]

Originally Posted by razorloves

use the one from post #9. then you can do what you said. no radio needed. yes, it's that simple.

so, using the .exe in post 9 will keep my CDMA radio intact and just wipe everthing else out?

[razorloves]

Originally Posted by Deltatristar500

so, using the .exe in post 9 will keep my CDMA radio intact and just wipe everthing else out?

yes .

[chunnel]

I just purchased a TP2 and want to install Mighty Rom, unless someone knows a better one for Verizon. Too bad NFSFAN doesn't make one... Anyway, the forum is poorly organized and I cannot find a definitive way to unlock the phone and install the new ROM. I'm assuming that this task29, or whatever it's called is the key. However, there are no complete instructions as to how to use task29 to unlock and install the new ROM. I do not know how to get into bootloader on this phone, nor can I find instructions. I have years of experience of ROM's on the Touch, the Touch Pro and now this. So far, this is seemingly the most complex and least explained. Please help if this is the right thread for such a question.

[mwalt2]

Originally Posted by chunnel

I just purchased a TP2 and want to install Mighty Rom, unless someone knows a better one for Verizon. Too bad NFSFAN doesn't make one... Anyway, the forum is poorly organized and I cannot find a definitive way to unlock the phone and install the new ROM. I'm assuming that this task29, or whatever it's called is the key. However, there are no complete instructions as to how to use task29 to unlock and install the new ROM. I do not know how to get into bootloader on this phone, nor can I find instructions. I have years of experience of ROM's on the Touch, the Touch Pro and now this. So far, this is seemingly the most complex and least explained. Please help if this is the right thread for such a question.

Task29 is a way of wiping your phone before flashing a new ROM. It helps with problems you may get if you just flash a bunch of custom roms. In the past, people flashed to a shipped rom to do the same thing. Task29 is faster and easier. It either flashes a radio or splash screen, and then wipes the memory that the ROM is written to. After it's done, you put the phone in bootloader and flash the new ROM. Bootloader is the same on the TP2 as the TP. Hold volume down and then press+hold the power button.

To use the task29 that flashes a splash screen (post #9 in this thread I believe), you double click Task29.exe and click yes/ok a few times.

[razorloves]

Originally Posted by chunnel

I just purchased a TP2 and want to install Mighty Rom, unless someone knows a better one for Verizon. Too bad NFSFAN doesn't make one... Anyway, the forum is poorly organized and I cannot find a definitive way to unlock the phone and install the new ROM. I'm assuming that this task29, or whatever it's called is the key. However, there are no complete instructions as to how to use task29 to unlock and install the new ROM. I do not know how to get into bootloader on this phone, nor can I find instructions. I have years of experience of ROM's on the Touch, the Touch Pro and now this. So far, this is seemingly the most complex and least explained. Please help if this is the right thread for such a question.

guess you're not so good with navigating through forums, so here's the link to the sticky thread for the unlocker http://forum.ppcgeeks.com/showthread.php?t=93252

[neilah]

Guys, I'm trying to flash an energy rom. I did it once without running task29 and for some reason the camera won't run. I get an error message that says either the camera certificate is not signed or is missing a component. Try and reinstall the camera.exe file.

So I thought I would try to run task29 first and reflash, however when I run task29 I get an "error message 240, file open" message.

Does anybody know what's going on here? Am I doing something wrong?

Little Help please!

I do have OliNex SPL 0.85 installed.

[neilah]

Oh Great! I finally got task29 to run, now I can't get an active sync connection.

All I get on my TP2 is the AT&T starup screen or the boot loader.

What do I do Now? I hope I didn't just brick this thing!

[cmajewsk]

Originally Posted by neilah

Oh Great! I finally got task29 to run, now I can't get an active sync connection.

All I get on my TP2 is the AT&T starup screen or the boot loader.

What do I do Now? I hope I didn't just brick this thing!

You don't need an ActiveSync connection to flash. As long as the bootloader (tri-color screen) has USB at the bottom when you are plugged in via USB you are all set to flash...

[ffkip911]

Originally Posted by neilah

Oh Great! I finally got task29 to run, now I can't get an active sync connection.

All I get on my TP2 is the AT&T starup screen or the boot loader.

What do I do Now? I hope I didn't just brick this thing!

this is exactly what task29 does---it takes virtually everything off of your phone---so no AS is on the phone any more.
1) DL the rom of your choice and 7zip into its own folder
2)run pagepool changer if you want
3)look for the file named RUU_signed.nbh
4)rename JUST THE RUU-signed not the extension to RHODIMG
5)copy this file and paste to the root of your Fat32 formatted SD card...make sure no other executibles are in the root---folders are fine.
6)pull the battery, put the batti back in, hold VOL down then hit power--it will kick you into bootloader and flash from SD
7)wait til you see it is finished, either pull the batti or red button reset---wait for it to configure


you've just flashed from SD


isn't AT&T a GSM phone-----do NOT FLASH A CDMA ROM

[Parasurfer1979]

Originally Posted by neilah

Guys, I'm trying to flash an energy rom. I did it once without running task29 and for some reason the camera won't run. I get an error message that says either the camera certificate is not signed or is missing a component. Try and reinstall the camera.exe file.

So I thought I would try to run task29 first and reflash, however when I run task29 I get an "error message 240, file open" message.

Does anybody know what's going on here? Am I doing something wrong?

Little Help please!

I do have OliNex SPL 0.85 installed.

Use the one in post number 9 on 1st page. I had the same problem as you...