Touch Pro CDMA Hard-SPL brought to you by CDMA Raphael Elite Team

[skasol]

Originally Posted by NexVision

Are u insuring u have microsoft activesync installed and synced prior to running? Also if using Vista since Vista sucks be sure to run as ADMIN to alleviate any chance of issue.

I tried this still no good, so I got it to get to the tricolor screen by putting the manual.exe file and then pressing the vol.down and soft reset and holding the power button. once it got there, it just hung at 0% and it gave me a 262 connection error that it couldn't communicate with the device.
do you think I have a defective device? eventhough I was able to sync with activesync.

I was told in another forum to put the .nbh file in the sd card and then it should work.

any suggestions/ideas?

Thanks in advance.

[NexVision]

Sounds like u got bad drivers plug the phone in and check device manager for questions marks or red x's also insure u r not using a usb hub. The likelyhood of your device being defective is rare based on what u said.

Also u can not flash new bootloader from entering using the method u stated I would go reread post one very thoroughly.

[skasol]

Originally Posted by NexVision

Sounds like u got bad drivers plug the phone in and check device manager for questions marks or red x's also insure u r not using a usb hub. The likelyhood of your device being defective is rare based on what u said.

Also u can not flash new bootloader from entering using the method u stated I would go reread post one very thoroughly.

Ok, I will check my drivers, but this happened in 2 different computers. one with vista and one with xp. if it was a bad driver wouldn't it give me the same problem when I sync with activesync?

I will check device drivers when I get back.
Thanks.

[flyers2114]

Originally Posted by NexVision

Are u insuring u have microsoft activesync installed and synced prior to running? Also if using Vista since Vista sucks be sure to run as ADMIN to alleviate any chance of issue.

Off topic.....Nex you working on a rom for the TP?

[NexVision]

Originally Posted by flyers2114

Off topic.....Nex you working on a rom for the TP?

Maybe if I didn't brick my TP. So until I get a replacement not yet.

[superevilllama]

Originally Posted by NexVision

Maybe if I didn't brick my TP. So until I get a replacement not yet.

How did you order your replacement? asurion? Just curious as I have one on the way

[NexVision]

Haven't gotten one yet but I plan on taking it to bestbuy and making them swap it since its under 30 days..

[skasol]

Originally Posted by NexVision

Sounds like u got bad drivers plug the phone in and check device manager for questions marks or red x's also insure u r not using a usb hub. The likelyhood of your device being defective is rare based on what u said.

Also u can not flash new bootloader from entering using the method u stated I would go reread post one very thoroughly.

I checked device driver, everything is fine there. when I am in tricolor screen it says security unlocked.
raph800
spl-0.37.000
MicroP-Hermann

and then it just hangs at 0% and gives me connection error 262 or update error.

I don't know what else to do so if anyone has any suggestions, I am all ears.

Thanks.

[NexVision]

Originally Posted by skasol

I checked device driver, everything is fine there. when I am in tricolor screen it says security unlocked.
raph800
spl-0.37.000
MicroP-Hermann

and then it just hangs at 0% and gives me connection error 262 or update error.

I don't know what else to do so if anyone has any suggestions, I am all ears.

Thanks.

Once again u really need to reread the first post u CANNOT FLASH A NEW BOOTLOADER FROM THE BOOTLOADER SCREEN U ARE ENTERING NOWHERE DOES IT SAY TO ENTER BOOTLOADER BY ENTERING THE KEY COMBINATION. I would say try being all eyes instead of all ears and read the post.

[lnchbx13]

Originally Posted by NexVision

I would say try being all eyes instead of all ears and read the post.

Sorry, just thought this was funny!