[ROM] 8/2/10 Generic JBTROM Bare Essentials WM 23569 Sense 2.5.2016 [UC/Sashimi] - Page 6

calexander3 · #51 (**permalink**) 07-13-2010, 02:24 PM

Quote:

Originally Posted by Lat

Thanks for throwing me in your credits as well jbt

Anyways, I'm downloading to give this a test run right now. I actually haven't flashed a new ROM since I released mine (too busy with other stuff), but looking forward to trying 2.5.2016.

[bleh, I just installed Windows 7 too; I have to use my SD card to flash now, or use VMWare/XP mode]

I flash from windows 7 all the time. Is there a problem I should know about?

calexander3 · #52 (**permalink**) 07-13-2010, 02:27 PM

Quote:

Originally Posted by Jbradthomas

Sense is original background I have made no changes to it.
Weird indian chick was in a wallpaper pack I downloaded some where. I like it so I use it.
Still not sure about that PRL thing

Glad you have it working on Verizon.

Well even with the PRL problem it is still a very good rom. I was using NFSFAN's rom until he stopped development. This one seems to be pretty close to the same speed. Keep up the good work.

Jbradthomas · #53 (**permalink**) 07-13-2010, 06:39 PM

Quote:

Originally Posted by Lat

Checked it out for a few hours, all looks pretty good

Only thing that I noticed was the SMS contact autocomplete didn't work...but you can always just use manila.

I didn't notice you included the carrier cab until after a bit though, so I may have used a bit of data accidentally

oh well.

SMS contact autocomplete works fine for me.

Jbradthomas · #54 (**permalink**) 07-13-2010, 06:43 PM

Quote:

Originally Posted by mdiaz33685

Everything seems to be working... good job..
except the sprint data prl... stuff again..

I flashed back to stock and all that, changed my radio and all so many times,,

but after the 1st flash,, that sprint prl changed my banner from metropcs to sprint...

I cant change it back... no harm really done, it still works just presents Sprint...
I can change it with personalizer 3.1 but it still says Sprint...

I 'am trying to figure out the PRL and Sprint banner thing. Somethings I' am still a noob at.

mdiaz33685 · #55 (**permalink**) 07-13-2010, 07:14 PM

I actually downloaded RaidZero's kitchen, dont know how to use... but.. when he posted this...

RZ_RAPH_kitchen_FINAL\EXT\Baseline\08_carrier\Spri nt

I think this is probably the problem, for me and others... if u can try to remove this to see if this helps with the connection issue...

Jbradthomas · #56 (**permalink**) 07-13-2010, 07:27 PM

Quote:

Originally Posted by mdiaz33685

I actually downloaded RaidZero's kitchen, dont know how to use... but.. when he posted this...

RZ_RAPH_kitchen_FINAL\EXT\Baseline\08_carrier\Spri nt

I think this is probably the problem, for me and others... if u can try to remove this to see if this helps with the connection issue...

So what you are saying is no carrier at all. Not even Generic.

mdiaz33685 · #57 (**permalink**) 07-13-2010, 07:32 PM

Quote:

Originally Posted by Jbradthomas

So what you are saying is no carrier at all. Not even Generic.

not sure how this all works, just noticed this in his folder and was wondering... if this is the stuff that is trying to load...

Jbradthomas · #58 (**permalink**) 07-13-2010, 07:35 PM

Quote:

Originally Posted by mdiaz33685

not sure how this all works, just noticed this in his folder and was wondering... if this is the stuff that is trying to load...

Hopefully Lat will give me some pointer on this. His ROM needs dcd provisioning cab.

Lat · #59 (**permalink**) 07-13-2010, 09:08 PM

Quote:

Originally Posted by Jbradthomas

Hopefully Lat will give me some pointer on this. His ROM needs dcd provisioning cab.

There isn't really an issue with the sprint provisioning ext cab you used...I mean, it worked fine with my Telus Mobility data =P

I believe the only requirement is that it dials #777 for data. You could probably modify the ext a little to make it a little more generic, or download a 'generic carrier cab' and convert it to an ext, but I don't think it's really that big of a deal.

I left the provisioning cabs out of my own ROM because I don't use data, and it makes it simpler for myself if other people just installed the cabs they need.

Jbradthomas · #60 (**permalink**) 07-13-2010, 09:17 PM

Quote:

Originally Posted by Lat

There isn't really an issue with the sprint provisioning ext cab you used...I mean, it worked fine with my Telus Mobility data =P

I believe the only requirement is that it dials #777 for data. You could probably modify the ext a little to make it a little more generic, or download a 'generic carrier cab' and convert it to an ext, but I don't think it's really that big of a deal.

I left the provisioning cabs out of my own ROM because I don't use data, and it makes it simpler for myself if other people just installed the cabs they need.

I 'am using Raidzero's original carrier package. There are no provisioning cabs in that package. Or do you mean PROVXML? I want to get this right before I post a generic ROM.