is there a way to recalibrate the screen or a known good sprint rhod 400 ts-calibrat.

**t0mmyr** · #1 (**permalink**) 07-28-2011, 12:25 AM

I just upgraded to FRX07 (clean install fresh files) without a ts-calibration file on my root sd card so that it would prompt me to calibrate the screen 1st boot...all went fine, i tapped all 5 points as closely as i could with the stylus right on the crosshairs but now it seems as if my lower half of the screen is mis-aligned vertically, if i tap an menu line or something usually something half an inch below clicks as if my stylus or finger was in a different spot, however the top half of my screen feels well calibrated....

is there a good way to recalibrate the whole screen? or perhaps someone has a good working ts-calibration file for the Sprint CDMA Touch Pro2 (Rhodium 400) that they can share? THANKSSSS

**arrrghhh** · #2 (**permalink**) 07-28-2011, 12:27 AM

Follow the steps in the FRX07 thread dude... the directions to recalibrate manually in there, and the calibration file attached is for RHOD. It was made on my 400, but should work for all RHOD's.

**t0mmyr** · #3 (**permalink**) 07-28-2011, 12:35 AM

theres about 3 frx07 threads and i didnt read anything about recalibrating after 1st boot, is that possible?

which post are you talking about that has a sprint calibration file attached?

**arrrghhh** · #4 (**permalink**) 07-28-2011, 12:38 AM

As far as I'm concerned, there's only one FRX07 thread. The others are just 'updated' to reflect FRX07...

http://forum.ppcgeeks.com/android-tp...dle-frx07.html

You can recalibrate whenever you want. Read the steps in the first post for manual calibration.

**[ACL]** · #5 (**permalink**) 07-28-2011, 12:37 PM

Quote:

Originally Posted by arrrghhh

As far as I'm concerned, there's only one FRX07 thread. The others are just 'updated' to reflect FRX07...

http://forum.ppcgeeks.com/android-tp...dle-frx07.html

You can recalibrate whenever you want. Read the steps in the first post for manual calibration.

Until the next rootfs is released, how about we throw that script to pull the calib points from winmo onto the user.conf file? This peeps need to calib only once, on winmo and thats it

.

can i get an amen !!!

kcwebmonkey · #6 (**permalink**) 07-28-2011, 12:42 PM

Sprint Touch Pro 2 Rhod400 ts-calibration file

Code:

821,860,197,868,500,517,829,172,191,171

I've had this configuration forever and it has worked great on every build....

**[ACL]** · #7 (**permalink**) 07-28-2011, 12:45 PM

Quote:

Originally Posted by kcwebmonkey

Sprint Touch Pro 2 Rhod400 ts-calibration file

Code:

821,860,197,868,500,517,829,172,191,171

I've had this configuration forever and it has worked great on every build....

because you are using the same phone. Each phone requires diff calib to be accurate.

Can i get an amen !!

**t0mmyr** · #8 (**permalink**) 07-28-2011, 12:49 PM

Quote:

Originally Posted by [ACL]

Until the next rootfs is released, how about we throw that script to pull the calib points from winmo onto the user.conf file? This peeps need to calib only once, on winmo and thats it

.

can i get an amen !!!

sounds like its worth an amen nigga

**arrrghhh** · #9 (**permalink**) 07-28-2011, 01:32 PM

Quote:

Originally Posted by [ACL]

Until the next rootfs is released, how about we throw that script to pull the calib points from winmo onto the user.conf file? This peeps need to calib only once, on winmo and thats it

.

can i get an amen !!!

Ah, I follow you. I'll try it out and see... Thanks for the suggestion!