[12-15-09]Android CDMA TouchPro: TEXT, TALK, data and wifi(RAPH800) Ported!!!

[relisted]

so does anyone know when we willl be anble to sms with android?

running sprint touch pro with caulkin visual kitchen

[orangekid]

Originally Posted by relisted

so does anyone know when we willl be anble to sms with android?

running sprint touch pro with caulkin visual kitchen

When the hero comes out.

[Plackslayer]

Originally Posted by orangekid

When the hero comes out.

We hope. As it is, with 1.6 we have CDMA as an option, I believe its just a matter of a bit more time before we figure out the implementation of it.

--PS

[mwcrz4]

When i run haret from my sd card it sort of boots but then keeps saying "waiting for sd card" and never fully boots...
anyone know whats wrong?

[nico4k]

Originally Posted by PropagandaX

Got this running, nice improvement from the last release. Interface works ok, hard to work with fingers on our high res touch pros, no network or phone, no response if phone goes to sleep black screen (edit: o wait theres the lock screen how the heck do you unlock.hmm?)

Press the Home key several times to unlock and wait a few seconds...that's how i unlocked.

Originally Posted by mwcrz4

When i run haret from my sd card it sort of boots but then keeps saying "waiting for sd card" and never fully boots...
anyone know whats wrong?

did you follow the instructions as listed in the first post? (downloaded the startup.txt file attached to the first post that is and replaced the one that came in the zip file).

[relisted]

damn. 1 more month right?

[Plackslayer]

Originally Posted by relisted

damn. 1 more month right?

I believe so yeah.

--PS

[Plackslayer]

I have tested out and compiled personally the latest kernel 9-26-09 and it fails miserably for CDMA - avoid it.

--PS

[mercado79]

Just thought I'd mention that working instructions for the Diamond can be found over in this thread in the Diamond section (thread started by toastcfh):

http://forum.ppcgeeks.com/showthread.php?t=84214

Basically, it requires a modified zImage file from a post on XDA devs (credit goes to MrPippy):

http://forum.xda-developers.com/atta...0&d=1252565799

...and also the start up script is different too. Take note of the MTYPE and msmts_calib values.

set RAMSIZE 0x08000000
Set ramaddr 0x10000000
set MTYPE 2040
set KERNEL zImage
set initrd initrd.gz
#
# The following kernel parameters are useful
# ppp.username - The username used to connect to the network when dialing #777
# ppp.password - The password used to connect to the network when dialing #777
# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller
# pm.sleep_mode - The mode used when the phone is off
# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,
# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt
# Default is 3, use 0 for best power savings
# board-htcvogue.panel_type - Panel type used to power the panel off and on
# 0=Don't power off the panel (Default)
# 1=Hitachi 2=Topoly 3=Samsung
# mddi.width - width of the scaled display
# mddi.height - height of the scaled display (these should be multiples of 16 for the camera to work I think)
set cmdline "msmts_calib=0x81.0x393.0x358.0x7D msmvkeyb_toggle=off mddi.width=320 mddi.height=480 lcd.density=240 ppp.apn=sprint ppp.username=username ppp.password=password no_console_suspend"
#set cmdline "no_console_suspend"
# fbcon=rotate:1
# console=ttyMSM0"
Boot
mkdir /proc
mkdir /sys
mount -t proc proc /proc
mount -t sysfs sysfs /sys
mount -t tmpfs tmpfs /dev
mdev -s
"ls -l /dev/mmc*"

I've attached my start up script below.

[thvoicwethin]

Thanks, I'll give this a try. I did not know that the phone had to be plugged in when booting this android version. Just keep it on the charger when booting and unhook when its done? My diamond boots into Linux, but then blacks out after it goes through some code... and occasionally shows the underscore... not sure it the charger thing is applied to this or not.