Locked out with new alltel rom

not1ofthepack · #1 (**permalink**) 10-08-2008, 09:05 PM

Ok the sorry goes, first unlocked the phone with

nueSPLTitan-100-2.47-pack-1, then updated to the lastest alltel rom. I then was going to try the iphone theme. It requires Hard-SPL-MFG. so I relocked the phone using nueSPLTitanRelocker-100-2.07-pack. So then I hard reboot, then start up RUU Hard-SPL-MFG. It put it in bootloader mode than then gives me Error (262): Update error.

I have tried to relock with nueSPLTitan-100-2.47-pack-1 and it seems to lock up in the bootloader, I have had it sitting here in the red/green/blue/white for 20 mins now.

Anything I can do?

**Lylej2k** · #2 (**permalink**) 10-08-2008, 09:12 PM

ok so your phone is re-locked currently? I may be wrong and someone can correct me if i am, but i think you need an updated bootloader to do that. I'm still a little confused by your post though.

not1ofthepack · #3 (**permalink**) 10-09-2008, 09:03 AM

my phone is re-locked. and I can not get back into it to change roms, it just hangs a 0% until it times out.

blueglide · #4 (**permalink**) 10-09-2008, 09:20 AM

Quote:

Originally Posted by not1ofthepack

my phone is re-locked. and I can not get back into it to change roms, it just hangs a 0% until it times out.

ON the bootloader screen...what bootloader version currently is displayed?

not1ofthepack · #5 (**permalink**) 10-09-2008, 09:46 AM

Tita100
Spl-2.07.0000
Cpld-9

**MrObvious** · #6 (**permalink**) 10-09-2008, 10:18 AM

Run Olipro 2.40 or nueSPL 2.47. If you have a SD card <=2GB IMO nueSPL is easier.

blueglide · #7 (**permalink**) 10-09-2008, 10:26 AM

Quote:

Originally Posted by not1ofthepack

Tita100
Spl-2.07.0000
Cpld-9

I assume you're trying to flash using a RUU...have you tried flashing a ROM using the SD card method? My only concern before doing that is what radio you may have on the device. When you flashed the newest Alltel ROM you installed a GPS radio. Flashing back to a stock OEM ROM without the GPS radio may cause problems...Somebody step in here and advise....been a long time since I unlocked and went through all that! I would reflash the nueSPL since you do that using the SD card and then flash your new stock or custom ROM.

not1ofthepack · #8 (**permalink**) 10-09-2008, 10:52 AM

Quote:

Originally Posted by MrObvious

Run Olipro 2.40 or nueSPL 2.47. If you have a SD card <=2GB IMO nueSPL is easier.

I have tried flashing with Olipro 2.40 using RUU and it hangs at 0% until it times out. I put nueSPL 2.47 in the root of the phone and run it, it comes up with the red/green/blue/white with:

TITA100
SPL-2.07No2Chem Titan SPL EVT
CPLD-9

but then that's it, it does not reboot. its been sitting on that screen for an hr now. when I did this before I let it sit for 10 mins and the powered down and rebooted. I checked the memeory card and it showed the TITAIMG.nbh it was around 24kbs. Then I soft reset to the red/green/blue/white and it just shows:

Tita100
Spl-2.07.0000
Cpld-9

ADDition.... I ran Olipro 2.40 from the MS-DOS Batch file. and it worked

SO I now have Olipro 2.40 yeahhhhh. now working un updating to nueSPL 2.47

blueglide · #9 (**permalink**) 10-09-2008, 11:20 AM

Quote:

Originally Posted by not1ofthepack

I have tried flashing with Olipro 2.40 using RUU and it hangs at 0% until it times out. I put nueSPL 2.47 in the root of the phone and run it, it comes up with the red/green/blue/white with:

TITA100
SPL-2.07No2Chem Titan SPL EVT
CPLD-9

but then that's it, it does not reboot. its been sitting on that screen for an hr now. when I did this before I let it sit for 10 mins and the powered down and rebooted. I checked the memeory card and it showed the TITAIMG.nbh it was around 24kbs. Then I soft reset to the red/green/blue/white and it just shows:

Tita100
Spl-2.07.0000
Cpld-9

Your post is a little confusing...you have NueSpl2.47 on SD card...put in phone and don't soft reset...push power/camera.soft reset and re-enter bootloader mode...see if phone sees TITAIMG.nbh on your SD card....

**MrObvious** · #10 (**permalink**) 10-09-2008, 12:59 PM

It sounds like your SD card isn't working right. Try formatting it quickly from Windows to FAT32 (you can back up the data to your hard drive), putting nueSPL on the card again as the only file, and then run it again. My SD card needed a reformat.