Unlockers for Custom Roms on Vogue 2.31(GPS) and 0.40(nonGPS)

[condelestat]

After running the new unlocker My Vogue will not recover from suspend mode. I have to soft reset. I have done a hard reset already. I am using ghettofreeryder's v15 rom. Had been for 2 weeks with out a hitch.
Any suggestions?

[Success100]

Originally Posted by KingGanon

i did this and it worked fine, cause i've flashed the titan before so i knew what i was doing. my only problem is that after i flashed, when the phone rebooted after the configuration, i started getting text messages from one of the short codes, 9130, and it hasn't stopped, it happens about every half hour. this didn't happen b4 the flash, and i wasn't doing anything on my phone before flashing. has anyone else had a problem like this?

p.s i even contacted sprint (my carrier) so that they can block it and supposedly they did but its still going on.

you probably were logged into some type of aim before you did the flash, thats where those messages are coming from

[condelestat]

Update: no matter what rom I load I still have the same problem.

[ImCoKeMaN]

Originally Posted by condelestat

Update: no matter what rom I load I still have the same problem.

The new unlocker 2.31 is only compatible with GPS roms, and you need to run the alltel exe to get the radio first. Otherwise you will have this error.

[condelestat]

Sorry for my ignorance. I stepped it back no problems so far. I'll go back and read s l o w e r , lol. thanks

[edbro]

Originally Posted by ImCoKeMaN

The new unlocker 2.31 is only compatible with GPS roms, and you need to run the alltel exe to get the radio first. Otherwise you will have this error.

I want to use the ROM that gives Rev A but not GPS, which unlocker should I use, 2.31 or .4? The RevA thread suggests using 2.31 but your statement above indicates other. I spent all day Sunday troubleshooting the freeze on standby issue when I used 2.31 for flashing a generic WM6.1 rom. Thanks.

[Red49er]

You can't get RevA without the 2.31 unlocker (unless you're on Alltel). GPS is only enabled by adding extra drivers.

[firefly4321]

For whatever reason I don't have any luck with the unlocker... right after the step disconnect and reconnect (I did that) my phone showed the rainbow color but then after the RUU launched does it thing then come back with and 260 connection error... everytimes...

Last time I was able to get around it by running the RUU before running the unlocker then wait until the RUU error out then return into recover mode then run the unlocker.

Then continue with the RUU recover mode (this is where it goes straigh to uploading the image to the phone)

So I suspect that forwhatever reason the RUU doesn't detect that my phone is already in the bootloader mode and just plainly refuse to connect at that point but if somehow I can skip the checking part trick the RUU to goes straight into uploading into the bootloader then it work fine...

If somebody can shed some light into this I would greatly appreciate it.

[jim2561]

Originally Posted by firefly4321

For whatever reason I don't have any luck with the unlocker... right after the step disconnect and reconnect (I did that) my phone showed the rainbow color but then after the RUU launched does it thing then come back with and 260 connection error... everytimes...

Last time I was able to get around it by running the RUU before running the unlocker then wait until the RUU error out then return into recover mode then run the unlocker.

Then continue with the RUU recover mode (this is where it goes straigh to uploading the image to the phone)

So I suspect that forwhatever reason the RUU doesn't detect that my phone is already in the bootloader mode and just plainly refuse to connect at that point but if somehow I can skip the checking part trick the RUU to goes straight into uploading into the bootloader then it work fine...

If somebody can shed some light into this I would greatly appreciate it.

you didnt modify or extract the exe at all did you? you just ran it etc...?

[firefly4321]

Jim, I did both, first time I ran it as is/after that I extract the thing, then take a look of the bat files to see what's going on and ran it from there.