CANT FIND MY PROs ESN

[jhgas]

Does anybody know how to read it with CDMA workshop, that´s how I got it for the diamond, I`m getting a new Pro, but I don´t know if reading from the same address 018E I think. Or is it a different address?

thanks

[jhgas]

Originally Posted by Krayziepop

Just an FYI, but the GetSPC program doesn't work on the Diamond/Pro. You will need a registry editor like PHM Regedit, then follow these instructions. Good luck

Change the following registry entries in:
HKEY_LOCAL_MACHINE\SOFTWARE\HTC\ATDbgLog
Enable: 1
LogMode: 1

* Wait a about 10 minutes (more time will not hurt), and soft-reset.

* Check to see that the file \Atlog\ATDbg0.txt has been created.

* Return the values back to what they were (most likely 0) waiting the same amount of time as above.

* Look in the ATDbg0.txt file and you should see a log of commands sent to the CDMA radio and there should be something like this somewhere in the file:

~~~~~~~~~~~SNIP~~~~~~~~~~~~
00:00:00 Tx:AT+HTC_RMSL=0\r
00:00:00 Rx:+HTC_RMSL: (###THIS WILL BE THE MSL###)\r\n0\r
00:00:00 Tx:AT+HTC_ROTKSL=0\r
00:00:00 Rx:+HTC_ROTKSL: 123456\r\n0\r
~~~~~~~~~~~SNIP~~~~~~~~~~~~


The numbers next to the Rx: +HTC_RMSL line should be your MSL

Escuse me...in what folder will the file be? \Atlog\ATDbg0.txt ... where would I find that folder?

Thanks

[banzaiwolfe]

Originally Posted by jhgas

Escuse me...in what folder will the file be? \Atlog\ATDbg0.txt ... where would I find that folder?

Thanks

It will be at the root of your device, same place you would find Program Files, My Documents, Windows, Etc...

[Krayziepop]

Just use file explorer and it will be on the same directory level as your Storage Card, and the above. NOTE - it may not open the first time you try. If it errors when you try to open the log file, it means the device is still writing to it and it is locked. Just make sure you set the registry back to 0 for the keys you changed and wait a few and soft reset again. It will kill the querying and should unlock the file at next boot.

[stroths]

Originally Posted by jhgas

Escuse me...in what folder will the file be? \Atlog\ATDbg0.txt ... where would I find that folder?

Thanks

It will be in the root directory of your phone's memory. As long as you have that registry key set, after you reboot you should see it listed.

[superevilllama]

emm that is far too much effort for me.. try the following, it doesnt require you to wait:


* Start your favorite pocket-pc terminal program (like pocketPutty - http://www.pocketputty.net/)
* Connect to com9 (Putty used default speed of 9600)
* type in AT+HTC_RMSL=0 and hit enter, your MSL will be displayed.

[Baffles]

Ah, I remember that method. Thanks for reminding me of it superevillama, it is much quicker and easier.

[jhgas]

Originally Posted by superevilllama

emm that is far too much effort for me.. try the following, it doesnt require you to wait:


* Start your favorite pocket-pc terminal program (like pocketPutty - http://www.pocketputty.net/)
* Connect to com9 (Putty used default speed of 9600)
* type in AT+HTC_RMSL=0 and hit enter, your MSL will be displayed.

Thanks. I tried that method once log timme ago (before I learned how to use Qpst or even installed CDMA workshop) and wasn´t able to make the terminal work. So I just plug the phone (in diag mode i guess) and run pocketputty? and choose port 9 right? and write down the command you mentioned?

Thanks again.

[Baffles]

I just wrote an app to get your MSL/SPC automatically and instantly. Should work on most every CDMA HTC device out there. Click the link in my sig.

[banzaiwolfe]

I had already pulled mine up via the registry edit, but thanks for this. It returned the same value as I had, so it does work.