Overclock TP2 in WM?

[neudof]

Originally Posted by Boominsvx

Let me know if I missed anything or anyone has questions.

Testing now

[nayr1482]

Originally Posted by Boominsvx

3. Using the registry editor, navigate to HKLM\Software\Msm7kcpuspeed and change safe_mode to 1. Here you can also set your boot options and increase your safe mode duration but the default speed should be fine.

safe_mode is part of OC_Auto, has nothing to do with SetCpuSpeed.
for SetCpuSpeed the key you probably want is BootTime (how much time before SetCpuSpeed waits until Overclocking IF you are using the /boot parameter).

Originally Posted by Boominsvx

5. Using total commander, navigate to your windows startup folder and HOLD PRESS setcpuspeed.ink. The intent is to rename it "Setcpuspeed.ink \boot" without quotes. When you press out of the keyboard /boot should disappear with no errors.

I would recommend after the press and hold to click Properties, then select the 'Shortcut' tab at the top. Then in the Target line add the /boot (spec before the backslash) to the end of the target entry...
Not saying your above way wont work...

Originally Posted by Boominsvx

6. Restart the phone. Do not try to run Haret yet or it will crash the phone and you'll have to make changes to the registry again. Just restart it and let Dualboot load. Remember, you're on a timeout so don't let it sit to long or the OC program will start and your phone will need to be restarted. If you need more time, increase Safe Mode Duration from step 3. (This is measured in ms, IE: 60000=1 minute)

Again, the key you want to be editing is BootTime.




Nice work though - I am sure many will appreciate this!


For those of you using the Script - the same thing SHOULD (someone will have to test - i dont run andriod on my tp2) work...just use the GUI to set your safe mode to on, and set your safe mode duration to a long value.

[Boominsvx]

Originally Posted by nayr1482

Nice work though - I am sure many will appreciate this!


For those of you using the Script - the same thing SHOULD (someone will have to test - i dont run andriod on my tp2) work...just use the GUI to set your safe mode to on, and set your safe mode duration to a long value.

Post edited.

Excellent observation nayr. I guess there will be a few that will have leftovers from the scripts from past attempts, but I didn't know which ones came in which bundle. This has been developed so quickly that things are all just mashing together lately. Thanks again man.

[neudof]

Originally Posted by nayr1482

For those of you using the Script - the same thing SHOULD (someone will have to test - i dont run andriod on my tp2) work...just use the GUI to set your safe mode to on, and set your safe mode duration to a long value.

I was trying this with the script and was not having any luck even with safe mode duration at max it was still locking up. I assumed it was because there was no 528 option..

[nayr1482]

Originally Posted by neudof

I was trying this with the script and was not having any luck even with safe mode duration at max it was still locking up. I assumed it was because there was no 528 option..

you know what...you are right. that is because the script sets to to a speed at boot and then waits.

i think i can change this. i think i can give you the option of keeping the cpu @ stock for x milliseconds.

let me see what i can come up with...

[neudof]

Originally Posted by Boominsvx

Let me know if I missed anything or anyone has questions.

I was able to finally get to Android!!
BUT
When I boot into WM my current CPU speed sets to 633.6 and in the registry I set it to 768..

I was getting a 768 using the script, am I doing something wrong?

[Boominsvx]

Originally Posted by neudof

I was able to finally get to Android!!
BUT
When I boot into WM my current CPU speed sets to 633.6 and in the registry I set it to 768..

I was getting a 768 using the script, am I doing something wrong?

Lets find out. In the registry, my values for my current setup are

boost_speed ( 38 )
Performance Level( 38 )
Throttle_speed (31)

This runs me at 729.6mhz at normal backlight on speed. How do those numbers match up? Does it bring yours to 729? Also, Make sure you don't have any scripts in your startup folder. setcpuspeed should be there though. Msm7k DOES NOT have to be enabled at boot. Check that out too.

Originally Posted by masetas

Can you tell me where can i get the cab you installed. Are you able to have run on battery power? Where did you install it too was it to your phone or sd card. have you had any problems with it recently

He's talking about msm7kcpuspeed v2 HERE and setcpuspeed 1.0d which can be found HERE.
Use a registry editor to change "HCKU/Control Panel/Phone/Sleep" to 0. This should solve your sleep issues.

[neudof]

Originally Posted by Boominsvx

Lets find out. In the registry, my values for my current setup are

boost_speed (3
Performance Level(3
Throttle_speed (31)

This runs me at 729.6mhz at normal backlight on speed. How do those numbers match up? Also, Make sure you don't have any scripts in your startup folder. setcpuspeed should be there though.

ahhh!
I did not change the performance level

[MixIsMobile]

Originally Posted by Boominsvx

Setting up Gen.Y Dualboot to function properly onstartup using setcpuspeed program for overclocking:

So I ended up getting it working last night. I guess I'll do a quick write up for anyone else looking into this. Gen.Y Dualboot will be telling you that Android is missing. I used the Blazin .ZIP file, but it should be the same for the .CAB file as long as it's a froyo build. Also, setting the phone up to allow time for dualboot to work.

I'M STILL WORKING ON BOOTING FROM WINDOWS MOBILE. This guide is only for Gen.Y running after a restart to boot into Android.

1. You should already have msm7kcpuspeed on your device, but for this to work, you MUST have setcpuspeed installed. If this program causes an S.O.D. after or during a phone call, use a registry editor to change "HCKU/Control Panel/Phone/Sleep" to 0. This should solve your sleep issues.

2. Install android to your Sd card if you haven't already, and Gen.Y Dualboot (Gen.Y DualBOOT WVGA v 1.0.6.0 - Storage Card) to your device.

3. Using the registry editor, navigate to HKLM\Software\Msm7kcpuspeed and under SetCpuSpeed the key you will see BootTime (how much time before SetCpuSpeed waits until Overclocking IF you are using the /boot parameter).. Here you can also set your boot options but the default speed should be fine.

4. While still in the registry editor, Navigate to HK CURRENT USER\Software\Gen.Y\DualBOOT and edit the data field of AndroidBootFolder to "\andboot\" without the quotes. This will allow Gen.Y to see you're android OS. (Note: If it still doesn't see it, you may need to use "\android\" instead. This is the folder on the root of your storage card that contains haret.exe.

5. Using total commander, navigate to your windows startup folder and HOLD PRESS setcpuspeed.ink. The intent is to rename it "Setcpuspeed.ink \boot" without quotes. When you press out of the keyboard /boot should disappear with no errors.


6. Restart the phone. Do not try to run Haret yet or it will crash the phone and you'll have to make changes to the registry again. Just restart it and let Dualboot load. Remember, you're on a timeout so don't let it sit to long or the OC program will start and your phone will need to be restarted. If you need more time, increase Safe Mode Duration from step 3. (This is measured in ms, IE: 60000=1 minute)

For those of you that want the easy button:



Let me know if I missed anything or anyone has questions.

did all of this, have it seein android, when i select android it acts like it's going to boot up, then stops

/bin/sh: can't access tty; job control turned of
/ #

what am i doing wrong

[matchstickredgti]

In regards for dual booting Android/Winmo while overclocked:

Originally Posted by Boominsvx

Setting up Gen.Y Dualboot to function properly onstartup using setcpuspeed program for overclocking:
5. Using total commander, navigate to your windows startup folder and HOLD PRESS setcpuspeed.ink. The intent is to rename it "Setcpuspeed.ink \boot" without quotes. When you press out of the keyboard /boot should disappear with no errors.

I'm not understanding this. I've got it the properties pulled up for setcpuspeed.ink, and in the target box I have the following:

"\storage card\program files\setcpuspeed\setcpuspeed.exe" /boot

What exactly am I renaming?