PPCGeeks

PPCGeeks (http://forum.ppcgeeks.com/index.php)
-   HTC Diamond (http://forum.ppcgeeks.com/forumdisplay.php?f=66)
-   -   SPC/MSL code of sprint diamond (http://forum.ppcgeeks.com/showthread.php?t=38151)

vboyz103 11-18-2008 05:48 PM

Re: SPC/MSL code of sprint diamond
 
Quote:

Originally Posted by blee0125 (Post 431602)
For Sprint Diamonds

Use CDMA Workshop and connect to the phone in diag mode.
Go to the "Security" Tab and hit "Read" SPC.
Select Universal Ram Method and Custom.
Address is: 018E:0190
Hit READ to find your SPC.

For Telus Diamonds I was told GetSPC works if you convert MEID to p-ESN but I haven't tried it myself.

Note if you are using the DEMO version of cdma workshop and your USB port is in COM10 or greater, you won't be able to read from phone because it's only for registered version.

c3hutson 11-26-2008 01:38 AM

Re: SPC/MSL code of sprint diamond
 
Quote:

Originally Posted by vboyz103 (Post 527714)
Note if you are using the DEMO version of cdma workshop and your USB port is in COM10 or greater, you won't be able to read from phone because it's only for registered version.

This...

ivan1.ruiz 11-26-2008 01:54 AM

Re: SPC/MSL code of sprint diamond
 
try this:

http://forum.ppcgeeks.com/showthread.php?t=43560

carta99 11-30-2008 11:36 PM

Re: SPC/MSL code of sprint diamond
 
good day r wateva time it is. i need help to get the spc from a htc touch pro and diamond. am in jamaica and i can't called sprint and i don't understand the instruction u guys ave made ok.
thanks in advance

statepkt 11-30-2008 11:58 PM

Re: SPC/MSL code of sprint diamond
 
Quote:

Re: OTA Sprint PRL update on Juicy
FYI, for all the Sprint people who don't what their MSL is:

I found this procedure on the xda forum and it works!!

I found a method that actually worked perfectly...

Use this method. I don't know who found it, but credit goes to them.

Change the following registry entries in:
HKEY_LOCAL_MACHINE\SOFTWARE\HTC\ATDbgLog
Enable: 1
LogMode: 1

* Wait a about 10 minutes (more time will not hurt), and soft-reset.

* Check to see that the file \Atlog\ATDbg0.txt has been created.

* Return the values back to what they were (most likely 0) waiting the same amount of time as above.

* Look in the ATDbg0.txt file and you should see a log of commands sent to the CDMA radio and there should be something like this somewhere in the file:

~~~~~~~~~~~SNIP~~~~~~~~~~~~
00:00:00 Tx:AT+HTC_RMSL=0\r
00:00:00 Rx:+HTC_RMSL: (###THIS WILL BE THE MSL###)\r\n0\r
00:00:00 Tx:AT+HTC_ROTKSL=0\r
00:00:00 Rx:+HTC_ROTKSL: 123456\r\n0\r
~~~~~~~~~~~SNIP~~~~~~~~~~~~


The numbers next to the Rx: +HTC_RMSL line should be your MSL
Try this

az93civic 12-06-2008 11:28 AM

Re: SPC/MSL code of sprint diamond
 
Quote:

Originally Posted by statepkt (Post 551751)
Try this


That worked the best :headbang:

stevedog1 12-21-2008 03:04 AM

Re: SPC/MSL code of sprint diamond
 
1 Attachment(s)
All those regedits, softresetting, and more regedits, and more soft resets takes way too long, and leaves room for error. Install this program here made by a fellow PPCGEEK member (Baffles I think, but his credential are included in the program itself). Install this, and it will get you your MSL on any HTC device within seconds. Hopes it saves a ton of you a ton of time! :headbang:

Try it out:

Trident 12-21-2008 12:09 PM

Re: SPC/MSL code of sprint diamond
 
Honestly, isn't it easier just to dial *2 and ask a CSR for the information?
If they give you a hard time, say goodbye and call back. I've never had to call more than twice.

stevedog1 12-21-2008 01:53 PM

Re: SPC/MSL code of sprint diamond
 
Quote:

Originally Posted by Trident (Post 591391)
Honestly, isn't it easier just to dial *2 and ask a CSR for the information?
If they give you a hard time, say goodbye and call back. I've never had to call more than twice.

Easier? :scratch: Never Call more than twice? No way

The program I listed 2 posts above takes just a few seconds to render your MSL.

Can't get any easier than that!

NewYorkLaw 12-21-2008 02:33 PM

Re: SPC/MSL code of sprint diamond
 
Quote:

Originally Posted by statepkt (Post 551751)
Try this

This worked for me, thanks.


All times are GMT -4. The time now is 07:36 AM.

Powered by vBulletin® ©2000 - 2025, Jelsoft Enterprises Ltd.
©2012 - PPCGeeks.com


Content Relevant URLs by vBSEO 3.6.0