BigJ's Revision 1.3h (ZELDA) updated: 8-28

[Maxx134]

Originally Posted by brandouno

BigJ, I am trying to downgrade from WM6 to this release, but when going in to bootloader 1.02, the ROM Update program never connects to my phone, and therefore the update doesn't happen. I've flashed maybe 30x, but never had this problem. Anyone have any ideas/suggestions?

Thanks,

B

I was having similar problem where in vista it would take long time to show up, then would not have the new rom listed in the upgrade to section... then would finally say something like unsupported device and would not upgrade.

I tried also with XP loaded inside a "virtual machine" in Vista as a host and got same thing.
Was running out of time to test further as I had 2 go out so I just ran the files off my older XP laptop and worked.

For Vista try this:
I forgot 2 try "right clicking" the "APACUpgradeUt_noID" file, selecting "properties", In "compatability" tab, check box to run in compatability mode for XP.
Also futher down check box for run prog as administrator.

I dunno if that would work but worth a try

EDIT:
woops I forgot to load activesync int the XP virtual machine. thats prob it and also Vista no longer uses activesyc that could be why noID program could not see 6700 as supported device... hmm.

[brandouno]

Thanks, Maxx.. I am between 3 XP boxes, and I can't get it to work on any of them. It's always worked on EACH of them in the past. I am gonna redownload the kitchen and try again.


/add stuff:
Wierd, I use BigJ's ROM and it upgraded just fine. Must be a problem with the kitchen ROM I cooked, or the download. Either way, you the man Big J. Thanks for making these ROMs.

[JBabey]

Originally Posted by brandouno

Thanks, Maxx.. I am between 3 XP boxes, and I can't get it to work on any of them. It's always worked on EACH of them in the past. I am gonna redownload the kitchen and try again.


/add stuff:
Wierd, I use BigJ's ROM and it upgraded just fine. Must be a problem with the kitchen ROM I cooked, or the download. Either way, you the man Big J. Thanks for making these ROMs.

im glad you got it working! ~> i patiently await a new adventure in ROM building!

[Jmckinney1976]

For Verizon users the jury was out as to whether or not upgrading the radio was beneficial. What was the final consensus?

[JBabey]

Originally Posted by Jmckinney1976

For Verizon users the jury was out as to whether or not upgrading the radio was beneficial. What was the final consensus?

the final consensus was to use Rasio 1.27 if you are having an issue. It seems about 50% of them work fine with 1.4 radio. If it doesnt work just roll your radio flash back, its pretty simple.

Hope that helps

[BenRivera]

VC is not announcing the caller id. Is anyone else having this issue or is there a solution to this?

[JBabey]

Originally Posted by BenRivera

VC is not announcing the caller id. Is anyone else having this issue or is there a solution to this?

its disabled by default, but you can easily re-enable it in the settings. I have personally tested this with and without a BT headset and it is working fine once its enabled. Hope this helps



=D>

[whankin2]

I upgraded, and for the most part all works well. However, when I place my phone in vibrate mode, I miss calls due to the phone not vibrating. Please advise, thanks.

Verizon 6700

[dancadman]

Originally Posted by whankin2

I upgraded, and for the most part all works well. However, when I place my phone in vibrate mode, I miss calls due to the phone not vibrating. Please advise, thanks.

Verizon 6700

Edit registry key: HKLM\Drivers\BuilIn\AllLEDMgr\ change Index to 1. If you search the threads, this has been covered several times.

[whankin2]

Great! The reg edit worked like a charm. Vibrates, now, thanks!