|
|
LinkBack | Thread Tools | Display Modes |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
Quote:
Hey Joel,For the LBS IP I have 0.0.0.0 and the LBS port I have 0 I can't help you with the QPST though. I don't seem to have it I have GPS enabled BTW |
This post has been thanked 1 times. |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
QPST is a qualcomm service tool, it's not on the phone. It's something you would have to install/setup on your pc to dock your touch to your pc and read all the extra info.
How long do your locks take? out of curiosity? |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
From a cold start it takes around 3 minutes. But after that on average about 10-15 seconds. The ROM I am running now seems to be the only ROM where the GPS does not die with time (knock on wood)
|
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
What rom out of curiosity? and radio?
Any extra hacks/info? |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
I forgot Aswell, open up your registry got to HKLM>Software>HTC>SUPL_AGPS.. What info do you have in here? Also does your agps seem to work? (you get locks that show you within a kilometer of your location before the GPS locks an actual satellite)?
If more than a few people on bell that have working gps can share this info along with your lock times, radio and rom I might be able to figure out why my GPS just plain sucks with the latest sprint radio and rom and also post an agps solution for bell users, as it was working prior to the flash( IT would position me in the general area of ottawa, not in the ocean.) I'm sure there is a missing link |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
Follow these instructions inside QPST to improve your GPS on bell...
http://wiki.xda-developers.com/index...me=TitanGpsFix Make sure you have the newest 3.42 radio installed...it will give best results! |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
I have tryed that a few times... and a bunch of variants..
What do you have in your registry i mentioned above, out of curiosity? I have about 4 ip's and ports for various providers. |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
You should NOT put an IP there! This function is more or less redundant.
Understand the way aGPS works...it uses the cellphone towers assistance to get you the data. In network terms, it uses something similar to DHCP. When you try to use aGPS, the phone receives a signal from the tower that will include the IP of a server that will help you in the location process. Forcing an IP will do more harm then good. If you don't get aGPS you are doing something wrong as all towers in Northern America support it. Make sure your radio is 3.42+ and you follow those steps...you should get locks of 7+ satellites within +/- 10 seconds on any provider. |
|
||||
Re: I need help from a Bell user using PRI 1.33 + GPS and has MSL, QPST would help to
I am running Dharvey 2.7.2 ROM, Soon going to 2.8.
I have used 3.35, 3.37, 3.42 and the best results came from 3.37.15. Recently I upgraded to the official Telus radio 3.41 and this is the best one I have tried. The only hacks I did was the PPST for Bell. Than a hard reset. The 3.42 radio gave me alot of problems and I could never get a accurate fix, 3.41 changed that. |
|
|
|