PPCGeeks - [12-15-09]Android CDMA TouchPro: TEXT, TALK, data and wifi(RAPH800) Ported!!!

PPCGeeks (http://forum.ppcgeeks.com/index.php)

- Windows Mobile Software (http://forum.ppcgeeks.com/forumdisplay.php?f=23)

- - [12-15-09]Android CDMA TouchPro: TEXT, TALK, data and wifi(RAPH800) Ported!!! (http://forum.ppcgeeks.com/showthread.php?t=61457)

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

Quote:

Originally Posted by Plackslayer (Post 1201775)

We hope. As it is, with 1.6 we have CDMA as an option, I believe its just a matter of a bit more time before we figure out the implementation of it.

--PS

well as far as hoping for stuff, once they get android fully cdma ported hopefully we can run actual hero ui on the poted android. That wouldn't suck.

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

damn. 1 more month right?

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

Quote:

Originally Posted by relisted (Post 1202364)

damn. 1 more month right?

I believe so yeah.

--PS

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

I have tested out and compiled personally the latest kernel 9-26-09 and it fails miserably for CDMA - avoid it.

--PS

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

Just thought I'd mention that working instructions for the Diamond can be found over in this thread in the Diamond section (thread started by toastcfh):

http://forum.ppcgeeks.com/showthread.php?t=84214

Basically, it requires a modified zImage file from a post on XDA devs (credit goes to MrPippy):

http://forum.xda-developers.com/atta...0&d=1252565799

...and also the start up script is different too. Take note of the MTYPE and msmts_calib values.

Code:

set RAMSIZE 0x08000000

Set ramaddr 0x10000000

set MTYPE 2040

set KERNEL zImage

set initrd initrd.gz

#

# The following kernel parameters are useful

# ppp.username - The username used to connect to the network when dialing #777

# ppp.password - The password used to connect to the network when dialing #777

# msm_sdcc.msmsdcc_fmax - The maximum frequency (in Hz) used by the SD controller

# pm.sleep_mode - The mode used when the phone is off

# 0=Power Collapse Suspend, 1=Power Collapse, 2=Apps Sleep,

# 3=Slow Clock and Wait for Interrupt 4=Wait for Interrupt

# Default is 3, use 0 for best power savings

# board-htcvogue.panel_type - Panel type used to power the panel off and on

# 0=Don't power off the panel (Default)

# 1=Hitachi 2=Topoly 3=Samsung

# mddi.width - width of the scaled display

# mddi.height - height of the scaled display (these should be multiples of 16 for the camera to work I think)

set cmdline "msmts_calib=0x81.0x393.0x358.0x7D msmvkeyb_toggle=off mddi.width=320 mddi.height=480 lcd.density=240 ppp.apn=sprint ppp.username=username ppp.password=password no_console_suspend"

#set cmdline "no_console_suspend"

# fbcon=rotate:1

# console=ttyMSM0"

Boot

mkdir /proc

mkdir /sys

mount -t proc proc /proc

mount -t sysfs sysfs /sys

mount -t tmpfs tmpfs /dev

mdev -s

"ls -l /dev/mmc*"

I've attached my start up script below.

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

Thanks, I'll give this a try. I did not know that the phone had to be plugged in when booting this android version. Just keep it on the charger when booting and unhook when its done? My diamond boots into Linux, but then blacks out after it goes through some code... and occasionally shows the underscore... not sure it the charger thing is applied to this or not.

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

Quote:

Originally Posted by thvoicwethin (Post 1206338)

After it boots you can remove it yes. If it is black, on my RAPH800 I just click back or home and one of the two brings up the screen.

Good luck.
--PS

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

Idk if i anyone had success with the android but it booted up for me...and i had phone.

CDMA worked on my build. idk how...but it did. 30 minutes later, it rebooted on me. now it won't boot up anymore :(

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

So i got Android to work...and when I did, i had phone capabilities. It was great. Although it only worked for 30 minutes before it restarted, it was fully functional. besides GPS, and WIFI and BLUETOOTH. the only thing is that when i turned the wifi function off, it restarted,. maybe thats what did it. but i has phone... i has happy.

Re: [9-9-09] Android for CDMA Touch Pro (RAPH800 and Diamond) Ported!!!

Quote:

Originally Posted by thvoicwethin (Post 1209763)

Were you using WiFi for the phone or were you actually connected to a G3 network?

--PS