I Flashed the Wrong Unlocker what to do

firebrain · #1 (**permalink**) 03-13-2008, 08:06 PM

I accidentaly flashed the Hard-spl olipro 1.40 on to a mogul with a 3.35 rom. I tried to reflash w 2.40 but it didnt work . exit_bl didnt work either. I cant relock because i cant get to activesync. what can i do

**SBR_L3GION** · #2 (**permalink**) 03-13-2008, 08:14 PM

do you have the advanced settings in activesync disabled and if that doesnt work,try flashin 3.35 again and then trying to unlock it.

**stroths** · #3 (**permalink**) 03-13-2008, 08:24 PM

As a last resort, you could flash a full Sprint 2.x rom (radio and all). Then you could use the correct unlocker and flash again.

firebrain · #4 (**permalink**) 03-13-2008, 08:24 PM

it wont let me boot wm its stuck in bootloader

**SBR_L3GION** · #5 (**permalink**) 03-13-2008, 08:29 PM

that is where you need to be just try updating in bootloader it works for me.

Spencer_Moore · #6 (**permalink**) 03-13-2008, 08:29 PM

try flashing via micro sd

mikldom · #7 (**permalink**) 03-13-2008, 08:29 PM

with that booter, (and I did the exact same thing), you have to load the official sprint 2.?? rom, then, you have to run a relocker to get the "official" boot rom of 1.06, then you can do the newest update straight from the tri color 1.06 boot rom screen.

it took me a couple of hours to figure all this out, but I was able to recover it just fine, and I have a vista machine!!!! with correct drivers of course.

hope that helps.. don't give up, just try some things and experiment.. Titans (moguls) are pretty forgiving and hard to "brick".. (permanently)

**blasphemous_prime** · #8 (**permalink**) 03-13-2008, 08:38 PM

Quote:

Originally Posted by firebrain

I accidentaly flashed the Hard-spl olipro 1.40 on to a mogul with a 3.35 rom. I tried to reflash w 2.40 but it didnt work . exit_bl didnt work either. I cant relock because i cant get to activesync. what can i do

i've had this exact same issue before with a leaked test rom, but i too couldn't relock it before i lost my 2nd model. now that it has been resolved, i can now run custom roms i normally don't run with an initial model i use with a guinea pig mogul... WOO HOO!

firebrain · #9 (**permalink**) 03-13-2008, 10:34 PM

where can you get 2.xx rom

journey · #10 (**permalink**) 03-13-2008, 10:37 PM

Quote:

Originally Posted by firebrain

it wont let me boot wm its stuck in bootloader

I had something similiar happen to me when I was installing 3.16 & the corresponding radio. I attempted to install the 2.4 BL but did not let it go all the way through the install. After the PPC was rebooted, it went back to the old BL, but this was after I had updated the radio. It would start to come up & hang.

Anyway, I found the OEM radio/ROM, and installed them. Once everything was 'back to normal', I started the whole process again.

As long as when you connect the USB cable that 'USB' is displayed in the lower section of screen, you just need to find a ROM image that is compatible with the 1.4 BL. Have you tried the new Spring ROM yet?