PPCGeeks
Page 7 of 8 « First 56 7 8
Show 40 post(s) from this thread on one page

PPCGeeks (http://forum.ppcgeeks.com/index.php)
-   Titan Development (http://forum.ppcgeeks.com/forumdisplay.php?f=57)
-   -   Should I enable REV. A in ##778#? (http://forum.ppcgeeks.com/showthread.php?t=20905)

jfolliard 03-13-2008 12:15 AM
Re: Should I enable REV. A in ##778#?
 
Quote:
Originally Posted by Baffles (Post 215053)
My whole area is Rev. A and i'm running Rev. A speeds, same old EVDO icon.

As far as where to run a speedtest, I find speakeasy.net/speedtest is faster than speedtest.net and tends to be more accurate.
question - is there a way to determine for sure if your geographical area is a Rev. A area?

Phreddo 03-13-2008 01:58 AM
Re: Should I enable REV. A in ##778#?
 
hmm, this is enabled, I think
http://www.speedtest.net/result/245703336.png
http://www.speedtest.net/result/245703805.png
1519 d/l, 124 up
am i really caring about uploads from my phone?
i swear, i'm about >< this close to totally dropping my landline.
man, if i was single i'd be set....

scotbotmosh 03-13-2008 09:02 AM
Re: Should I enable REV. A in ##778#?
 
2 Attachment(s)
Quote:
Originally Posted by intrlude (Post 215564)
Hey bro, when in that screen. Press view info, highlight the section that states data parameters. That's where Rev. A. is at. You must have gone in edit, MSL. to make changes, otherwise your just viewing what's there.

The screen shot I posted IS from the Data Parameters page...that is why I am confused, I DO NOT have a REV A setting? wierd...I do have the updated ROM and Radio though...What did I miss?

bakntyme 03-13-2008 10:05 AM
Re: Should I enable REV. A in ##778#?
 
Quote:
Originally Posted by scotbotmosh (Post 215877)
The screen shot I posted IS from the Data Parameters page...that is why I am confused, I DO NOT have a REV A setting? wierd...I do have the updated ROM and Radio though...What did I miss?
Did you do a Sprite Restore after loading the new ROM? It will remove the Rev. A setting from the EPST.

scotbotmosh 03-13-2008 10:43 AM
Re: Should I enable REV. A in ##778#?
 
Quote:
Originally Posted by bakntyme (Post 215958)
Did you do a Sprite Restore after loading the new ROM? It will remove the Rev. A setting from the EPST.
Ha...crazy you should mention that I DID use Sprite restore...argh...Hard Reset comming right up...damn...

NxlKing2304 03-13-2008 11:08 AM
Re: Should I enable REV. A in ##778#?
 
Quote:
Originally Posted by scotbotmosh (Post 216016)
Ha...crazy you should mention that I DID use Sprite restore...argh...Hard Reset comming right up...damn...

I upgraded to the 3.35 ROM and Radio and then loaded NoChem's 5051 build. I found that the 5053 build was very lagy and locked up alot. Anyways, I don't see the Rev A logo either. I did do a sprite restore but i did the ROM one. and only updated the personal databases and email. should i not have done that?

bakntyme 03-13-2008 04:45 PM
Re: Should I enable REV. A in ##778#?
 
Quote:
Originally Posted by NxlKing2304 (Post 216058)
I upgraded to the 3.35 ROM and Radio and then loaded NoChem's 5051 build. I found that the 5053 build was very lagy and locked up alot. Anyways, I don't see the Rev A logo either. I did do a sprite restore but i did the ROM one. and only updated the personal databases and email. should i not have done that?
Usually the ROM option on Sprite Restore would have worked properly...but in this ROM it removes the Rev. A setting.

scotbotmosh 03-13-2008 05:16 PM
Re: Should I enable REV. A in ##778#?
 
Yup I did a hard reset and there it was...I then just selectivly restored from my Sprite backup data..

Genjinaro 03-13-2008 05:28 PM
Re: Should I enable REV. A in ##778#?
 
LOL I tried everything with Sprite.

Long story short, I had to start from scratch, a lot of error/conflicts came, even in my barest "Safe Mode". :p

cororumrex 03-13-2008 11:06 PM
Re: Should I enable REV. A in ##778#?
 
I did about three tests at three different servers. once through on disable and once on enable.
download speeds were about the same maybe a 5% variance up or down.
Upload speeds were also pretty consistent.

I did notice that my Ping times were twice as long though.
100-175 ms - disable
200-325ms - enable


All times are GMT -4. The time now is 04:00 AM.
Page 7 of 8 « First 56 7 8
Show 40 post(s) from this thread on one page

Powered by vBulletin® ©2000 - 2025, Jelsoft Enterprises Ltd.
©2012 - PPCGeeks.com


Content Relevant URLs by vBSEO 3.6.0