CC20 Doesn't load properly - Image and logs attached
 

I was trying to load CC20 with UMDL 2.3. The UMDL gets to Download image 100%. Then it just stops - no error message.

This is the log:

PDA Device Found!
[Port : 1]EBoot version = 01.35
-------------------------------------------------------------------------------------
PDA Device 1 ready to download!
-------------------------------------------------------------------------------------
PDA Device 1 ready to download!
-------------------------------------------------------------------------------------
PDA 1 starts downloading...
Don't plug it out until the label becomes blue!!!
-------------------------------------------------------------------------------------
EBOOT will be written.
PDA will be written.
PHONE will be written.
-------------------------------------------------------------------------------------
Downloading EBOOT...
[Port 1] Checksum Check ::


-------------
(Device 1 log)

Device name:5&2b986538&0&1
EBoot version=01.35
Start downloading...
PDA-Starting updating EBOOT...
PDA-Downloading EBOOT...

---------------
This is what the phone looks like - a picture of an orange triangle with an exclamation point in it over an outline of a phone. And just one line of the green progress bar.

http://img21.imageshack.us/img21/5592/image226bx.jpg


Additional info: If i press the little reset button on top then hold down the 2 buttons to format - it will slowly load up and boot into the phone. But obviously something didn't go right.

I had been following instructions from here: http://www.modaco.com/content/i910-specifi...m-verizon-i910/

any ideas?

Re: CC20 Doesn't load properly - Image and logs attached
 

did you try flashing again?

Re: CC20 Doesn't load properly - Image and logs attached
 

is it a verizon wireless cdma i910 cause other wise it wont wor right.

Re: CC20 Doesn't load properly - Image and logs attached
 

did that...didn't work

Re: CC20 Doesn't load properly - Image and logs attached
 

my screen has a different screen when flashing and loading so i am thinking you have another 910 or a 900

Re: CC20 Doesn't load properly - Image and logs attached
 

i have a 910

Re: CC20 Doesn't load properly - Image and logs attached
 

where's the usb cable? that might be your problem... :-P

Re: CC20 Doesn't load properly - Image and logs attached
 

in case you were serious i disconnected it to take the picture

Re: CC20 Doesn't load properly - Image and logs attached
 

lol only joking. one thing you might try is downloading cc20 from another source. that one might be corrupt for some reason.

Re: CC20 Doesn't load properly - Image and logs attached
 

+1 and from the photo yes he has a verizon i910... try a different cc20 and make sure u have the usb drivers

Re: CC20 Doesn't load properly - Image and logs attached
 

can you post some links to the CC20?

Re: CC20 Doesn't load properly - Image and logs attached
 

http://theidoctor.org/omnia.html

opps its not on there... let me find some

Re: CC20 Doesn't load properly - Image and logs attached
 

Re: CC20 Doesn't load properly - Image and logs attached
 

ok so before i have been using UMDL 2.3 this time i decided to just double click the file i910WM6.1.REV10.CC20.VZW.img and this is what happens:

I get this message from my log:

PDA Device Found!
-------------------------------------------------------------------------------------
PDA Device ready to download!
Please Press Start Button if You want to download image now...
-------------------------------------------------------------------------------------
PDA 1 starts downloading...
Don't plug it out until the label becomes blue!!!
-------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
Step 1. Eboot image Downloading
Downloading EBOOT...
EBOOT image downloaded.
Step 2. PDA image Downloading
Downloading PDA region #1(DISKIMAGE)...
PDA Image Length : 123969807
PDA image downloaded.
Step 3. Customer image Downloading
Downloading CSC...
GetSize : 2967552
CSC finished.
Step 4. Phone image Downloading
Downloading PHONE...
Switch USB to Phone Success...
Error! PhoneUSB Detect Failed
Port Create retry (25)
Port Create retry (24)
Port Create retry (23)
Port Create retry (22)
Port Create retry (21)
Port Create retry (20)
Port Create retry (19)
Port Create retry (18)
Port Create retry (17)
Port Create retry (16)
Port Create retry (15)
Port Create retry (14)
Port Create retry (13)
Port Create retry (12)
Port Create retry (11)
Port Create retry (10)
Port Create retry (9)
Port Create retry (8)
Port Create retry (7)
Port Create retry (6)
Port Create retry (5)
Port Create retry (4)
Port Create retry (3)
Port Create retry (2)
Port Create retry (1)
Port Create retry (0)
Download failed!!

The computer says USB device not recognized and the phone ends up with the same image as i posted earlier. The program says port create failed.
-- i do have the samsung USB driver installed by the way. ](*,)

Re: CC20 Doesn't load properly - Image and logs attached
 

Re: CC20 Doesn't load properly - Image and logs attached
 

do u have the usb drivers... and allow usb connections clicked off?

Re: CC20 Doesn't load properly - Image and logs attached
 

yes and yes

Re: CC20 Doesn't load properly - Image and logs attached
 

make sure it is a usb 2 port and than make sure the setting are correct on both computer and phone as said in instructions from doctor. Also make sure when you do that that it has downloaded the correct driver. I have vista and it has to detect for both usb modes. THere is one in active sync and also on your phone. Try hard reset first and if alread have done that try a soft reset by pulling battory out while phone is on and unpluged waiting 30 seconds and than us the umdl thing and put the cc20 at the botom of step one in the unified image file. detect detect device plug in and turn on. but the hard reset should fix any problem on the phones end if it is a phone setting. If that still does not work i am guessing it is on the computers end. Could it be a security setting on the computer. Chances are if no one else has had this problem it is somthing you should be able to fix. If you can drop files like a usb port than it should work. oh ya i think it should come up as a mass storage device as your last drive letter at the bottom of my computer and not as a smartphone if setting are correct. I will have to check its been so long.

Re: CC20 Doesn't load properly - Image and logs attached
 

I can make the phone show up as a drive letter.

when it gets to switch phone to usb i keep getting usb device malfunctioned or is not working properly. I do have usb 2.0 i have tried different ports (and my ports are working). I think if that image on my phone can be identified - maybe thats whats causing all my problems?

Re: CC20 Doesn't load properly - Image and logs attached
 

I mentioned this over on Modaco.

Your phone is done. :(

Turn it in for a new one.

Re: CC20 Doesn't load properly - Image and logs attached
 

Damn... Omina's are dropping like flies...! :(

Re: CC20 Doesn't load properly - Image and logs attached
 

Do you know why this happenedto him? I was going to flash my girls omnia but not if this is going to happen. Is there anything he did wrong that i should avoid?

Re: CC20 Doesn't load properly - Image and logs attached
 

This can happen to the phone at any point in time that it is being flashed. That said, follow the directions and it should go well.

No, I don't know what happened to him.

Re: CC20 Doesn't load properly - Image and logs attached
 

Ouch well thanks for the response but thats a risk id rather not take. I wish flashing this was as easy as my diamond every problem ive ever had i was able to fix. Id hate to have to tell my girl that her phone is junk now and has to wait for a replacement she needs it everyday for work.

Re: CC20 Doesn't load properly - Image and logs attached
 

Any phone can brick at any time from a flash. There is no more risk bricking an Omnia, than a Diamond.

I flash 10-12 times a week. Thats 40 to 48 times a month, and far more than most people will flash in their lifetime, much less this phone.

No brick yet.

Re: CC20 Doesn't load properly - Image and logs attached
 

Honestly im sure i would be fine but i just get nervous when its not my stuff. I would be alot more confident if i knew what he did wrong to avoid it.

Re: CC20 Doesn't load properly - Image and logs attached
 

I doubt that he did anything wrong. The phone would have probably had problems down the line if he hadn't flashed.

Some people have actually tried to brick their phones and were unsuccessful. They had some issue not associated with flashing and didn't want to go in to VZW with CC20 showing as a ROM.

Ted

Re: CC20 Doesn't load properly - Image and logs attached
 

OP, did you have your connection settings to Active Sync, or USB mode. A lot of people flashed there's with that setting on Activesync. but some of us at the beginning had it set to USB mode and our flashes went through. Might be worth a shot.

Re: CC20 Doesn't load properly - Image and logs attached
 

It's there . . . the "Firmware" link #1. It looks like he removed the CC20 torrent (link #2).

Ted

Re: CC20 Doesn't load properly - Image and logs attached
 

ahh i see it now=D>

Re: CC20 Doesn't load properly - Image and logs attached
 

Thanks to everyone who offered thier help. It appears my phone is dead. Well im off to call verizon for a new one....

Re: CC20 Doesn't load properly - Image and logs attached
 

There should be no problem getting another one. When I requested one (for nonexistent Hard Reset probs) I received a factory refurb within 48 hours. Less the back cover and battery, which you transfer over from your phone.

As it turned out, I figured out the flexing of the Call/End buttons while hard resetting and wound up sending the replacement back.

Good luck.

Ted