Verizon / Sprint silicon case available - Page 2

kabuk1 · #11 (**permalink**) 02-03-2010, 07:27 PM

I'm planning on ordering the blue version of this actually, funny seeing it on here. I'm also hoping to find it elsewhere, I hate waiting for shipping.

I have a hard plastic case like this & the buttons really arent any harder to press with it on.

**TweetyBear** · #12 (**permalink**) 02-03-2010, 07:41 PM

yeah i had hard rubberized case for my tp and luckily it was easy to remove. my guy has a hard plastic case for his tp2 now and it's hell to remove the bottom cover. i'm hoping this silicon case will be easier to remove. and i like the look too. too bad it dont have yellow (myfave)

**TweetyBear** · #13 (**permalink**) 02-04-2010, 01:49 AM

i bit the bullet and ordered one anyways. hope it fits well!

**MrHawaii** · #14 (**permalink**) 02-13-2010, 05:32 AM

Did anyone who ordered this receive it yet? If so, what are your thoughts?

FYI, I ordered the blue and smoke colored ones and am still awaiting it.

**MrHawaii** · #15 (**permalink**) 02-21-2010, 04:43 AM

I received my cases and are very satisfied with them. The blue is actually kind of purplish. The smoke matches the Sprint devices well. It feels much better in my hands than when I had a hard snap on case. The hard case that I have covered the proximity sensor so it disabled it. This case works with it. Volume buttons and power button are easier to press since the buttons are raised with the case on rather than recessed. The fit is pretty snug and I believe they were actually made for the www version of the device. The lower part of the bottom cover is cut a little incorrectly. It fits, but the hole where the charging port is was small like it was meant for the phones with only the charging port on the bottom and not both charging port and 3.5 mm headset jack.

I fixed this easily by placing the cover on the phone, since it is clear traced a line around the bottom of the ports. Looked sort of like this \_____/, then used a diagonal cutting pliers to snip it off along the line. Hope it helps.

dskansas · #16 (**permalink**) 02-22-2010, 05:31 PM

Quote:

Originally Posted by elmerfudpucker

I use Invisashield myself, no problems, no bulk.

+100....the only way to go

subzero1313 · #17 (**permalink**) 02-22-2010, 05:43 PM

I ordered 1 of these...waiting for it. Ill post my thoughts when I get it

**Adrianh85** · #18 (**permalink**) 02-22-2010, 05:55 PM

yeah as if the tp2 isnt big enoght!! looks good just wish this device was thiner!!

lefty11 · #19 (**permalink**) 02-22-2010, 07:21 PM

Quote:

Originally Posted by Adrianh85

yeah as if the tp2 isnt big enoght!! looks good just wish this device was thiner!!

I have had this case and it barely adds to the profile compared to any other case for the tp2 i have seen. I have had rubberized snap ons, clear snap ons, body glove and they all have issues with the top left snap not being extremely well fitting. This case ( I have 2 in smoke grey) is BY FAR the best fitting two piece case around so far I have seen for the TP2 . My two bottom holes were perfectly exposed on my Sprint TP2 , every hole was lined up perfect. It was actually easy to put on and fits snug without needing a grooved connection for the top and bottom piece like some other two piece silcone caes for the old TP used to have. I have no vested interest in these but they look great and feel great and so far fit great. If you ordered one for Sprint and it did not fit well, then send it back or look to make sure you have it completely on. The only bad thing is that it takes 2-3 weeks to get here from Hong Kong. Other than that, these are the best so far if you do not like holsters .