|ROM|¯`·.¸¸.- Energy -.¸¸.·´¯ * |July 4| 21916|29022 * Sense 2021 + flavors

[jotarou1]

Comstar:
I can host about 4 GB's of the ROM's you have. If you pick some out and let me know. I will get you an FTP setup with my host so you can upload the files. I can do about 35 GB's of transfer before I will have to stop the downloads (I have a max of 50 GB's of transfer per month but I will have to monitor as I get over 35 GB's).

Let me know,

Originally Posted by Comstar

I think it's a good idea. If someone can figure out a place I will upload them. I looked again and there are 70 roms - 11gb.

[ShowYouHow]

Energy.RHODCDMA.28244.Sense2.5.Feb.27.7z on Sprint TP2 - but I've noticed this happening in the past few NRG roms I've tried.

When switching to a different tab on the slider, or changing orientation, the screen temporarily gets a graphic glitch that stretches out graphics looking similar to CRT scanlines (rows of graphics are spaced a pixel apart) Is this a known issue or do you suspect a hardware problem with my refurb?

This is noticed upon a Task29 + ROM Flash with no O/C - and MyPhone sync, email accounts and provisioning added only.

Thanks in advance. (I'm not crazy about the extra features of Cookie 2.0 - but the Sencity "in-progress" Cookie 2.0 is looking sweet. I'm hoping there is some arrival of that soon)

[Monfro]

Originally Posted by ShowYouHow

Energy.RHODCDMA.28244.Sense2.5.Feb.27.7z on Sprint TP2 - but I've noticed this happening in the past few NRG roms I've tried.

When switching to a different tab on the slider, or changing orientation, the screen temporarily gets a graphic glitch that stretches out graphics looking similar to CRT scanlines (rows of graphics are spaced a pixel apart) Is this a known issue or do you suspect a hardware problem with my refurb?

This is noticed upon a Task29 + ROM Flash with no O/C - and MyPhone sync, email accounts and provisioning added only.

Thanks in advance. (I'm not crazy about the extra features of Cookie 2.0 - but the Sencity "in-progress" Cookie 2.0 is looking sweet. I'm hoping there is some arrival of that soon)

No problems here on the same rom.
In february i flashed all the wm6.5.x standard roms...and no problem at all.

[KIOWA69]

Originally Posted by marcoss

hello, i just installed this room for my tp2 on boostmob, mms picture messaging is not working, do i need to install any cab?

sounds like you need to either find a provisioning cab for boost mobile or use one of the ones that's built into the roms, now what i don't know is if there is a provisioning cab for boost mobile or if they can use one of the other cellphone carrier cabs or what so it would be nice if someone else with boost mobile could chime in and let you know what they are doing to get mms working.

Originally Posted by ShowYouHow

Energy.RHODCDMA.28244.Sense2.5.Feb.27.7z on Sprint TP2 - but I've noticed this happening in the past few NRG roms I've tried.

When switching to a different tab on the slider, or changing orientation, the screen temporarily gets a graphic glitch that stretches out graphics looking similar to CRT scanlines (rows of graphics are spaced a pixel apart) Is this a known issue or do you suspect a hardware problem with my refurb?

This is noticed upon a Task29 + ROM Flash with no O/C - and MyPhone sync, email accounts and provisioning added only.

Thanks in advance. (I'm not crazy about the extra features of Cookie 2.0 - but the Sencity "in-progress" Cookie 2.0 is looking sweet. I'm hoping there is some arrival of that soon)

my guess would be that you are either installing something that's causing that to happen, changing a setting that's causing it, could be bad downloads, and are you installing any type of backed up programs, contacts or anything like that?

thats where i would start, as a matter of fact what i would do is wipe the phone and flash to stock, hard reset, task 29 and flash to new rom, hard reset and then start installing anything your going to install one cab or whatever one thing at a time and try to narrow it down to what's causing it. while you are on the stock rom i would check everything out and see if it's working fine, then i would say it has something to do with all the stuff i wrote above, might have to find another rom within the NRG series that works for you besides the 28xxx series of roms.

just have to remember that if you don't see anyone else having the issues that you are having it's either something you are doing, bad download or something could be wrong with the phone.

[akeaw3000]

Originally Posted by marcoss

hello, i just installed this room for my tp2 on boostmob, mms picture messaging is not working, do i need to install any cab?

It will work, according to masetas. Check out this post.

[akeaw3000]

Originally Posted by GernerPSU

Ever since I flashed Feb 19th, my data stopped working. Are there any steps out there to reset the data provisioning or whatever I have to do?

Not really sure, but I would try:
1. Run Carrier Provisioning
2. Update Profile & PRL
3. Run AutoData Config (I have absolutely no idea what this does... it does nothing on my phone, but sounds like it might help) "Settings" home tab > "Other" Miscellaneous settings > AutoData Config
4. If all else fails, task29, flash stock ROM, reflash, & wipe.

[stevey5036]

Changelog for the Feb 28 roms?

[NinjaDuck]

Originally Posted by stevey5036

Changelog for the Feb 28 roms?

none, but no major differences from the last change log.

[swlaraut]

Originally Posted by GernerPSU

Ever since I flashed Feb 19th, my data stopped working. Are there any steps out there to reset the data provisioning or whatever I have to do?

Originally Posted by akeaw3000

Not really sure, but I would try:
1. Run Carrier Provisioning
2. Update Profile & PRL
3. Run AutoData Config (I have absolutely no idea what this does... it does nothing on my phone, but sounds like it might help) "Settings" home tab > "Other" Miscellaneous settings > AutoData Config
4. If all else fails, task29, flash stock ROM, reflash, & wipe.

This happens to me every time I use NRGZ provisioning cab. Before you reflash try this. Go to:

Start>settings>connections>connection(again,not a typo), click on "manage existing connections" and you should get a screen like the one posted here. Make sure "auto pick" is selected and hit OK. It should work now.

I don't know why, but for me its always set to " phone as modem" after I provision. Hope this fixes it for you.

Also its not hard to add a new connection if needs be, but I won't go into that unless its needed.

[kern417]

Reference 3/1 update available #ftw
thx nrg!