PPCGeeks - How To's: Unlocking, Relocking, Flashing, Dumping and Troubleshooting

PPCGeeks (http://forum.ppcgeeks.com/index.php)

- CDMA Diamond Development (http://forum.ppcgeeks.com/forumdisplay.php?f=67)

- - How To's: Unlocking, Relocking, Flashing, Dumping and Troubleshooting (http://forum.ppcgeeks.com/showthread.php?t=36062)

Re: How To: Unlocking, Relocking, and Flashing

Yea I know, but its seams so easy to do it this way...and I haven't been able to flash any other way. Either way it goes I'm flashin now and thats all I wanted.
Thanks to all!

Re: How To: Unlocking, Relocking, and Flashing

Quote:

Originally Posted by tobeychris (Post 822632)

Sorry puff, but you lose too!

"Oh no! 404 - Page not found"

My turn: http://www.htc.com/us/SupportDownloa...at=2&dl_id=530

Actually, the here link works--Does this update the radio too? and was this built into MR 4.8? How bout the audio hotfix?

Re: How To: Unlocking, Relocking, and Flashing

Quote:

Originally Posted by Stoney60 (Post 877756)

Actually, the here link works--Does this update the radio too? and was this built into MR 4.8? How bout the audio hotfix?

yes it's an official update so it updates the radio as well to 1.11.00f. Not sure about whether Mighty implemented this rom into his release, probably not if I had to guess.

Re: How To: Unlocking, Relocking, and Flashing

Help with MSL For Palm Centro
I need help getting the MSL for my Palm Centro I was given. I called Sprint with all the info they needed and was turned down. Under no circumstances would they give me the code; only in the store and I don't have time to go. Anyway, I have tried just about everything (downloads, syncing, etc.) and I need a quick fix. I can provide the ESN for any pros or employees. Just need a little help.

Thanks

Re: How To: Unlocking, Relocking, and Flashing

Is anyone here having any problems flashing with Windows 7 RC1 x64? As soon as the progress bar comes up in the RUU utility (ie it becomes disconnected from Windows Mobile Device Center), Windows starts installing a QPST driver which seems to disconnect the phone from the update utility. That causes it to fail and I am stuck on the bootloader screen. If I plug the phone back into USB, RUU still cannot find the phone. I've searched and have found several people say they've been flashing with Windows 7, so I don't know why I am having this problem.

Re: How To: Unlocking, Relocking, and Flashing

Quote:

Originally Posted by uhdt2007 (Post 878750)

if the rep knows and follows policy, they wont give it to you if u just straight ask for it...
i recommend you check out BAFMSL Grabber :D

Quote:

Originally Posted by mwalt2 (Post 883501)

Did you try disabling advance functionality in USB to PC?

Re: How To: Unlocking, Relocking, and Flashing

I am no able to un lock my touch diamond. I followed all the directions. I have Dot net 3.5 SP1 installed and active sync connected error 202 connection when i run unlock.
Hard Reset before i started. Any thing I could try?
Could my phone be unlocked new?
Thanks

Re: How To: Unlocking, Relocking, and Flashing

Quote:

Originally Posted by rlparker (Post 885045)

hello

the as error 202 is covered on page 4, post 35. it means you are not establishing a connection properly between your diamond and pc. there are several tips throughout this thread that may fix your problem.

Re: How To: Unlocking, Relocking, and Flashing

Quote:

Originally Posted by puff (Post 883884)

Did you try disabling advance functionality in USB to PC?

Where would that setting be? I let it install the QSPT drivers, and the RUU program was able to flash successfully. However, when I tried to flash again, it was not able to communicate with the device and I was stuck in bootloader mode. I don't have this problem in Vista or XP, so I'm not sure what would be causing it.