Quote:
Originally Posted by ooxteme
New EnergyROM lineup from now on... 5 flavors to choose from. Releasing new ROMs with this stuff tonite
|
thanked, here we go again!!! Yahoo... actually, may sit this one out.. not a theme guy, we'll see.
.....
per your requests a couple pages ago...
WMLongLife settings.
Download here:
http://forum.xda-developers.com/showthread.php?t=478519
Obviously if you talk on the phone straight for 5 hours, this will not help you.
all thanks to Chainfire, a legend programmer
@ xda..!
Download here
READ THE FIRST 3 POSTS TWICE!!!
VERY IMPORTANT POINTS:
Uninstallation
Before uninstallation, there are two things you should do:
1) Open the Band Switcher application, and switch to "3G (auto)" mode
2) If you have roaming options enabled, make sure you are NOT roaming when uninstalling
~~~~~~~~~~~~~~
I have done my best to let WMLongLife be as least annoying as possible. The idea is (with the default settings) that a band-switch should occur only once in a phone 'session'. Where by a session I mean a screen-on / use device / screen-off cycle
*** DO NOT: set WMLonglife to switch from EV to go back to 1x when the application is closed.
~~~~~~~~~~~~~
- Copy the WMLongLife.cab file to your device and open it to install it.
- Go into WMLongLife configuration and make sure to check/configure the following options:
- Radio / Radio chip model (and GSM band for Samsung radios)
- Radio / Restart push mail after band switch
- Roaming - All options
These are likely to be detected and set correctly, however I advise you check them anyways. Details about these options can be found in the configuration section below.
- Optional: Go to Start -> Settings -> Personal -> Buttons, and assign a button to the Band Switcher application
- Soft-reset
The configuration options in WMLongLife are supposed to have "sane defaults", the setup which I expect will work best for most users.
Please note some beta testers have reported they need to soft-reset twice after installation/upgrade before WMLongLife works
~~~~~~~~~~~~~~~~
Screen / Vibrate notifications
Very handy for debugging! When this option is enabled, WMLongLife will vibrate when loaded, when ready, and when switching. It may take WMLongLife over a minute to be actually loaded after the device is booted. When it is, it will vibrate very shortly three times (it may feel like a single long vibration). When WMLongLife is ready to allow automatic switching, it will vibrate shortly twice. When WMLongLife actually switches bands, it will vibrate once.
~~~~~~~~~~~`~~~ MY SPRINT SETTINGS ~~~~~~~~~~
The key to my settings was to simply enable 3G on screen light..
3 top tabs
CENTER TAB (cogged wheel) & what should be selected
RADIO
Radio chip model: (CDMA)
3G (auto)
850/1900
Sprint
unck restart push mail (for me.. you can ck it if u need)
SCREEN (select these)
Switch to 3G when the screen turns on
Return control to WMLongLife when the screen turns off
Vibrate Notifications
APPLICATIONS:
Switch to 3G on whitelisted app launch
Wi-Fi: unchecked
USB: unchecked
Data: (only one) disconnect idle connections (60 seconds)
Roaming checked (only one)
~~~~~~~~~~~~~
3RD TAB
When you use an application for the first time, it'll ask you for the settings.. nice.. I simply
uncheck wifi & usb & ensure 3G is checked (I don't use wifi or usb, you may, so ck per your needs)
I set internet sharing to maximum of 60 min & hit the power switch so it stays on when screen is off (I use wifi hotspot always)
These are my settings, hope it helps y'all.
Also, reread the buzz settings, when you turn on your tp2, it'll buzz 3, 2, 1 & then you know it's ready.... also still having a tiny issue on sometimes after a boot, i'll take 20 seconds to auto data (although it turns on Ev right away).
3G = EV (top taskbar)
You will see 1X often. These may not be the best settings by far, but they don't cause major issues for me & then I was happy.
If someone else gets this thing tuned down better please feel free to advise!!
:>))