PPCGeeks
Page 5 of 6 « First 34 5 6
Show 40 post(s) from this thread on one page

PPCGeeks (http://forum.ppcgeeks.com/index.php)
-   HTC Touch Pro (http://forum.ppcgeeks.com/forumdisplay.php?f=63)
-   -   [Guide] USCC TP to EnergyROM (http://forum.ppcgeeks.com/showthread.php?t=92323)

money711 12-07-2009 01:25 PM
Re: [Guide] USCC TP to EnergyROM
 
Quote:
Originally Posted by Deadpool14 (Post 1380537)
I followed these steps but when i get to the MMS options the only thing I see is about call back numbers nothing about the servers. I am tapping the wrong options button?



Thanks.
EDIT: I forgot to mention I did run the programs mentioned above.
Did you get this figure out? If not which energyrom are you running? I normally go with 21877 and I am currently about to set up my MMS now for the Dec 7 rom.

EDIT: Mine is working with no problem.

hippy43 12-15-2009 11:49 AM
Re: [Guide] USCC TP to EnergyROM
 
Quote:
Originally Posted by murducky (Post 1260645)
POST 2: USCC Radio Info

Stock Radio
Full List of CDMA Radios by strra here: http://forum.ppcgeeks.com/showthread.php?t=74422



How to rate Radios / How can I view my signal levels?
##33284# is the DEBUG menu. If you are prompted for a password, enter 183729. Under here you should look at the following 3 sections (the closer to 0 you are, the better):
Rx Power
Rx Ec/Io
Rx FER
OK,, dumb question. You say "##33284# for debug menu. Where do you type this in? If I dial that string, I get a no longer available message. What am I missing here?

Thanks in advance.

murducky 12-15-2009 12:43 PM
Re: [Guide] USCC TP to EnergyROM
 
Quote:
Originally Posted by hippy43 (Post 1414866)
OK,, dumb question. You say "##33284# for debug menu. Where do you type this in? If I dial that string, I get a no longer available message. What am I missing here?

Thanks in advance.
yup not working for me either now, must be something with the new builds i'm on 28011.

Im Packing 12-15-2009 06:14 PM
Re: [Guide] USCC TP to EnergyROM
 
I'm using EnergyROM's 28014 Leo Maxmanila Dec. 15 release, but when trying to install the "Remove Picture mail cab" it says that it can't install. I tried the device first, then storage card, but both failed. Any help please?

money711 12-17-2009 09:58 AM
Re: [Guide] USCC TP to EnergyROM
 
Quote:
Originally Posted by Im Packing (Post 1415728)
I'm using EnergyROM's 28014 Leo Maxmanila Dec. 15 release, but when trying to install the "Remove Picture mail cab" it says that it can't install. I tried the device first, then storage card, but both failed. Any help please?
you should save it on your desktop or laptop then move it over through active sync. also i have done this method i would install the arcsoft first then try the remove picture mail i dont know why it dont work all the time but i did notice that it seems like sometimes you have to do things in a different order just follow normal steps after you get that to install.

Im Packing 12-19-2009 02:19 AM
Re: [Guide] USCC TP to EnergyROM
 
Quote:
Originally Posted by money711 (Post 1420098)
you should save it on your desktop or laptop then move it over through active sync. also i have done this method i would install the arcsoft first then try the remove picture mail i dont know why it dont work all the time but i did notice that it seems like sometimes you have to do things in a different order just follow normal steps after you get that to install.
I have no problems copying it to my device or storage card. It's when I open the file and try to run it it will not install to either the Device nor storage card.

money711 12-21-2009 10:44 AM
Re: [Guide] USCC TP to EnergyROM
 
Quote:
Originally Posted by Im Packing (Post 1424734)
I have no problems copying it to my device or storage card. It's when I open the file and try to run it it will not install to either the Device nor storage card.
have you tried to upload the cab directly from the device also? If so try installing another cab file to see if any will install on your device.

orrisland 01-08-2010 08:27 PM
Re: [Guide] USCC TP to EnergyROM
 
Thanks for the help, but i still cant get the mms to work:(

murducky 01-09-2010 12:27 AM
Re: [Guide] USCC TP to EnergyROM
 
Quote:
Originally Posted by orrisland (Post 1472398)
Thanks for the help, but i still cant get the mms to work:(

what rom you using? is it manila 2.1 or 2.5 ?

swlaraut 02-16-2010 07:42 PM
Re: [Guide] USCC TP to EnergyROM
 
Quick note: if you live in Southern Oregon and have not done a *228, do so your EV now.


All times are GMT -4. The time now is 07:21 PM.
Page 5 of 6 « First 34 5 6
Show 40 post(s) from this thread on one page

Powered by vBulletin® ©2000 - 2025, Jelsoft Enterprises Ltd.
©2012 - PPCGeeks.com


Content Relevant URLs by vBSEO 3.6.0