Help stuck in bootloading screen
 

i must be daft, or getting there. I need some help please. when i boot up what i see on the tri colour screan is

RAPH800
SLP-0.37.0000
MicroP-Hermann(LED) V0c85
MicroP-Hermann(Key) v0685
PSOC-Raph STAGE-EVT v20

Upgrade ROM code error
please try again

I must have done something wrong like reading when it's late and flashing a wrong ROM.
when i try to flash RUU and it gets to image version on the top it's blank and hangs on the leading screen. I have tried to boot from an sd card and it hangs in the loading screen, if i try a larger file i get and error

00028002 on the loading screen with not allowed

How can i re flash the whole system if it's possible i think i flashed 6.5 gsm by error. Is my phone a paper weight now.

Re: Help I think i bricked my phonw
 

ya sounds like you flashed gsm and im sure if you look at the rom it is, so you tried flashing a CDMA nbh from sdcard?

Re: Help I think i bricked my phonw
 

Yes I have tried it hangs on the loading screen forever. So i got a second sdcard formatted it to fat 32 still hangs

Re: Help I think i bricked my phonw
 

try unlocking again using sdcard method. better yet try relocking then unlocking.
http://forum.ppcgeeks.com/cdma-tp-up...a-sd-card.html

Re: Help I think i bricked my phonw
 

I have tried both nbh files it just hangs on the loading screen when i try ruu loader from pc when i get to the page showing versions current version is blank if that helps

Re: Help I think i bricked my phonw
 

so you cant even re lock? is that what you mean by "both nbh files?"

Re: Help I think i bricked my phonw
 

yes i have tried to relock and unlock even tried Raphael_CDMA_HSPL_037 again with no luck. when i try the nbh from Hermann_C_SPRINT_WWE_1.03.651.3_RS1.03.15F_SPCS_1. 53_PRL6063_Ship.exe
by renaming it i get an error on the loading screen 00028002 not allow then it goes back to tri colour screen. when I try to load from the pc via usb it gets to 1% then shut's down and goes back to tri colour screen. Last time around i was getting corrupt file error's on the Raphael_CDMA_HSPL_037 instead of the usuall hang on loading screen. Although it seems sync. my computor does not recongnise the phone but the loaders seem to find the unit i am using vista 64 bit, and have installed all the drivers that are needed.

Re: Help I think i bricked my phonw
 

ya i think your bricked but maybe someone can prove me wrong. (i hope)

Re: Help I think i bricked my phonw
 

I hope so also. Thank you for your help i was hopeing that i could reload the complete operating system from scratch ](*,)

Re: Help I think i bricked my phonw
 

I think i might have messed up the operating system by trying 6.5 gsm insted of 6.5 cdma is there a way to reverse this.

Re: Help I think i bricked my phonw
 

What exactly did you try to do that caused the problem? Links and filenames would be helpful. If you tried to unlock your CDMA phone with the GSM unlocker, you are bricked. If you tried to flash a GSM radio or a GSM ROM containing a radio to your CDMA phone, you are bricked. Other then that, I don't now of a way to end up bricking your phone (other than hardware issues).

Re: Help I think i bricked my phonw
 

iunlocked the phone using Raphael_CDMA_HSPL_037 that went fine. Then i flashed from bell to sprint because im moving that went fine also. The issues stated when i flashed it the third time " should have quit after the 2nd". I flashed it using WinMo6.5(Build 23529)_plusExtras that was the mistake i now know it was gsm and the phone is cdma. The phone is in a loop touch pro starts's then it reboot's. I can get it into the boot screen, cannot acess the phone via the comp but it does sync. I have tried

Hermann_C_SPRINT_WWE_1.03.651.3_RS1.03.15F_SPCS_1. 53_PRL6063_Ship.exe
MightyROM6_Herman
Raphael_CDMA_Relocker
SPRINTRELOCKER
task29 Sprint TP Radio V1.03.15F Shipped R
task29 VZW Raphael Shipped rom v1.03.03v R
task 29 with splash screen
Bell Stock ROM TP

if i use the sd card it just hangs on the loading screen if i use the comp. i get to screnn, the current information about your PDA phone and my image Version is blank. I choose update pick the version that's listed and it sync's up, get's to 1% then reboots putting the phone back into the toch pro link loop. On the comp. I get ERROR(294): Invalid vendor id.
Any help would much appreciated .

Re: Help I think i bricked my phonw
 

Flashing a GSM ROM with no radio will not brick your phone. I've done it before when I forgot to change OEMXIPKernel from a GSM to CDMA in a ROM I built once. It did the constant reboot thing. I just put it in bootloader (hold vol. down and push/hold the power button), connected to usb, and flashed a new ROM. Most kitchens these days make it pretty hard to put a radio in the ROM. Where did you get "WinMo6.5(Build 23529)_plusExtras"? I googled it and all I get is a bunch of torrents.

Have you tried unlocking your phone again? I would 1) re-lock 2) flash a shipped rom from whatever carrier branded the phone 3) unlock with proper unlocker 4) try to flash a custom ROM.

Re: Help I think i bricked my phonw
 

I have tried to flash the original rom from bell but it habgs on the loading screen same thing happens with the locker and unlocker. as for the last flash that caused me problems it was from another site serves me right.
It was to update to version 1.9 and 6.5 on the operating system, but it turns out it was a gsm file. The boot procedure works it just wont finish what it starts 0% only herman file gets to 1% then the phone goes into loop again. I might be flashing wrong bell rom but i dont think so.

Re: Help I think i bricked my phonw
 

Don't relock the phone thats not going to solve anything.

You only need to run the unlocker once and only need to relock if you are heading to the service department to hide the fact you flashed a ROM!

Communication errors are usually USB related not the phone. Now you could have a bad USB port on the phone but I would try another USB cable and a reboot of the desktop before you flash.

Oh also never try to flash with the phone plugged into a USB hub, always connect directly to the computer. Sometime HUBs will screw up the solid connection needed. There is a good reason why the installer says don't disconnect the phone during install.

If you still get TriColor you are not bricked.

Re: Help stuck in bootloading screen
 

what I'm getting when try Raphael_CDMA_HSPL_037/or relocker is "error 262 communication error" after it hangs at 0%. I'm using vista 64 and i am using the same cable and port that was used to unlock the phone flash it a second time successfully but not the third so i dont think it's the cable. If i try to load from sd card just hangs at 0%. I have tried the following:

Bell Stock ROM TP
Bell_Elite_RC1_RC1_21234_20090624
task29 Sprint v1.12.34F
Hermann_C_SPRINT_WWE_1.03.651.3_RS1.03.15F_SPCS_1. 53_PRL6063_Ship
Raphael_CDMA_Relocker
Raphael_CDMA_HSPL_037

They load alright get to the page where it shows my current image version, and it is blank. I pick the version to update it starts, phone and comp switch to loading screen and it stay's at 0%. After a while it now comes up with an error that say's ERROR (294) : INVALID VENDOR ID. Near the exit button just above the exit button is a code

B a3-RBRK<567-SQEVc568-RBRK<5670 if that can help in any way.

Only Hermann_C_SPRINT_WWE_1.03.651.3_RS1.03.15F_SPCS_1. 53_PRL6063_Ship gets to 1% before it goes into the reboot startup loop where all i see the the touch pro screen then reboots, all the others just stay at 0% with the error above .
These are just a few i have tried MightyROM4_06.20.09_Herman, task29 and others but it just wont sync up. Although it say's usb on phone and they do seem to start to sync when i first plug in the phone using the usb my mobile sync center does not recognize the phone nor can i access any of the files because it's not on my list under comp.

Any ideas would be greatly appreciated

Re: Help stuck in bootloading screen
 

Should i resign myself to a new bookend or paper weight. I have tried the hard reboot also. Getting into the start up where it loads all the manufacturer defaults after pressing vol Up then goes back into loop cycle unless i boot it into the tri color screen. I have tried all the options listed above with no results. Ive been reading about a gold card sd would this perhaps fix my issues.