Re: USB Charging Cradle For CDMA Touch Pro2
 

Mine will sync and charge. They are like 5 bucks on ebay. Cant complain..

Re: USB Charging Cradle For CDMA Touch Pro2
 

yep, I get an error if I plug too many things into my 4way usb splitter saying it can't charge certain devices.
It charges my bluetooth headset and my wife's instint s30 fine, but the tp2 it says it can't handle. you might try switching which usb port you are plugged into and move it to a primary one if not on it already.

Re: USB Charging Cradle For CDMA Touch Pro2
 

There's a thought. As a last resort you could try a powered USB hub and use an external power supply to provide the additional power needed to charge the phone while still maintaining your activesync connection.

Re: USB Charging Cradle For CDMA Touch Pro2
 

I'll go thru the same charging process using the supplied TP2 cable with various USB ports on my confuser and see if that makes any difference - will report back.
So far, my 'ultimate' solution' is to just buy a whopper power strip with plenty of separation between plugs. Just looking around my workstation here, I have 13 things plugged in! Cripes, I need my own nuclear reactor...
Thanks guys.

Re: USB Charging Cradle For CDMA Touch Pro2
 

Old TP1 Dock + Dremel Tool on the "filled in" plastic on the right side = TP2 Dock.

Re: USB Charging Cradle For CDMA Touch Pro2
 

ON charging multiple devices off a hub from a SINGLE USB port from your computer...its a simple electrical thing. You get the voltage...but NOT the charging amps (milliamps I guess in this case.) If you use a hub, I'd suggest use a powered one...so its not drawing from your computer's USB port.

On charging dock (usb type) I'm using Seidio's and it works with a naked TP2 as well as one that is cased in a Seido case. Love it!!

Re: USB Charging Cradle For CDMA Touch Pro2
 

From Wikipedia's entry on USB power:

Power

The USB 1.x and 2.0 specifications provide a 5 V supply on a single wire from which connected USB devices may draw power. The specification provides for no more than 5.25 V and no less than 4.75 V (5 V±5%) between the positive and negative bus power lines. For USB 2.0 the voltage supplied by low-powered hub ports is 4.4 V to 5.25 V.[33]
A unit load is defined as 100 mA in USB 2.0, and was raised to 150 mA in USB 3.0. A maximum of 5 unit loads (500 mA) can be drawn from a port in USB 2.0, which was raised to 6 (900 mA) in USB 3.0. There are two types of devices: low-power and high-power. Low-power devices draw at most 1 unit load, with minimum operating voltage of 4.4 V in USB 2.0, and 4 V in USB 3.0. High-power devices draw the maximum number of unit loads supported by the standard. All devices default as low-power but the device's software may request high-power as long as the power is available on the providing bus.[34]
A bus-powered hub is initialized at 1 unit load and transitions to maximum unit loads after hub configuration is obtained. Any device connected to the hub will draw 1 unit load regardless of the current draw of devices connected to other ports of the hub (i.e. one device connected on a four-port hub will only draw 1 unit load despite the fact that all unit loads are being supplied to the hub).[34]



What they are saying is that you may only have 100ma available on each USB port (not enough to charge the phone). If you are only using one port per hub, then you may have the full 500ma available. Keep in mind there are internal hubs in the PC (check out your device manager if you doubt this).

So, if you are using one of your front-panel USB ports for something else, don't use another for charging the phone. Same with the back-panel ports. I usually use all back-panel ports for everything else, and only one front-panel port for charging devices. Even then, only one specific port up front will actually charge the device. You can sometimes see a special USB logo showing the USB icon with a solid/dashed line below it. This indicates a powered port.

This is also why some 2.5" external hard drives require a separate power adapter on some computers/ports but not others.

Re: USB Charging Cradle For CDMA Touch Pro2
 

All makes sense Tybalt, but my Fuze charged fine from the USB ports (both back and front) and my Zune also seems to have no trouble getting a full charge. I used the same USB port for the TP2 as I always use for the Zune - very different outcome. My next charge test is to use the TP2 cable from that same port and see what happens.

For those trying to use your old cradle, make sure the shape is correct, not just the jack position. Mine is perfectly flat and square to hold the Fuze...will not work well for the rounded TP2.

Re: USB Charging Cradle For CDMA Touch Pro2
 

I have some cords that limit the charge to a trickle.

Re: USB Charging Cradle For CDMA Touch Pro2
 

Here is CDMA version for sprint, verizon, us cellular, telus:

http://cgi.ebay.com/BATTERY-CHARGER-...item518e5deb1c

nakedcellphone also has several extended batteries - make sure you get the right version - they have different batteries and cradles for cdma vs gsm