Please Help :)
Hey everyone I screwed up. I have an unlocked ppc6800 qwest originally. And I went to upgrade the rom and it got to 12% then the phone errored (error num 920) now the phone wont boot back it wont recover can someone please help. I am an IT so I have experiance in different things so being techy is ok.
|
Re: Please Help :)
darn sorry error 290
|
Re: Please Help :)
what were you trying to upgrade it with?...do you have to correct bootloader and radio if trying to use one of the custom roms
|
Re: Please Help :)
please i need help my htc mogul 6800 is dead i only see a warning ALIGN SCREENtap the trarget firmly and accurately at each location an the screen. the target will continue to move until the screen is aligned
|
Re: Please Help :)
I need help just reset my htc 6800 and now only leaves the screen to align the screen and does nothing but try to help me do not have to go back to living my Mogul,please my htc mogul 6800 is dead i only see a warning ALIGN SCREEN tap the target firmly and accurately at each location an the screen. the target will continue to move until the screen is aligned,i need help
I would be grateful if someone helps me solve this problem |
Re: Please Help :)
fox-1, you could have started your own thread instead of hijacking this one?
Were you possibly adjusting the registry settings to adjust the sensitivity of your screen, and went too low? What happened right before this occured? |
Re: Please Help :)
Quote:
|
Re: Please Help :)
Quote:
late, Coz |
Re: Please Help :)
Quote:
|
Re: Please Help :)
It is in bootloader mode. and i havent a clue what rom was on it before. i got the phone from a friend awhile back and it was unlocked. and where can i download a rom for it?
|
Re: Please Help :)
Quote:
You seriously need to read up. If you don't you're gonna end up with a very nice paperweight which once used to be a phone. Make sure the bootloader says "Olipro 2.40" or "nueSPL 2.47". The you need to have a radio at least 3.35.04 or higher. Then you can flash a custom ROM. READ READ READ READ! Unless you want to end up with a bricked Mogul, learn all you can! Have a good day :) |
Re: Please Help :)
what it says when i turn it on is...
TITA100 SPL-1.20.Olipro. So this means what? Thanks everyone btw for helping. |
Re: Please Help :)
You need to use Olipro 2.40 NOT Olipro 1.20 FLash an old ROM then use 2.40
|
Re: Please Help :)
Quote:
|
Re: Please Help :)
the device isnt connecting to activesync. so i cant transfer the files needed.
|
Re: Please Help :)
Then use nueSPL
|
Re: Please Help :)
Well im new to this whole thing to but after reading up about a bunch of stuff i decided to give it a try and ended up with the same problem. your phone is still not unlocked, it was just put in bootloader mode and if you want to reset it back to manufacture settings hold down the two buttons above the windows and okay buttons and push in the reset for a few seconds with your stylus (known as a hard reset). This should reset bring up two options, use the qwerty keynoard to hit R then when its done hit the space bar. Go through the tapping the screen then go here and read up:
http://http://forum.ppcgeeks.com/showthread.php?t=33857 It is done by GAMedics and how i managed to pull it off with a little help from xda. You need to get version 2.4 of Olipro and then run it to unlock your phone then get a Sprint rom and use Rom Utility Update (RUU) to flash it, then do a soft reset (just push in the reset button with the stylus) when the tap to configure screen comes up then put in bootloader mode (hold power, camera, and push in reset for a few seconds) and upload your custom rom. Another thing is make sure your roms are using a blank RUU becuase i tried opening the sprint rom through a rom already using RUU and got hung up with the splash screens becuase it never flashed the radio but the OS rom instead. These instructions should work fine with your phone becuase i have the same one through qwest and just got new xv models through Verizon becuase qwest is dropping their own service through sprint. |
Re: Please Help :)
even after i do the hard reset back to manufac. settings it still loads to bootloader. Am I doing something incorrectly? Or missing a step?
|
Re: Please Help :)
maybe try hooking up your phone to the pc while its in bootloader and try running a rom with the RUU and go through the steps to try and correct an error which it will probably show up and should get your phone out of bootloader mode. this might help, not to sure as mine never got stuck on that screen after i did a hard reset.
|
Re: Please Help :)
i tried but it fails to send file. and when i boot it flashes a gray screen for a sec that says no image file. then goes to bootloader.
|
Re: Please Help :)
on mine when it said failed to send file it then went to a correction screen in RUU after hitting next in the RUU and i followed those steps. if that doesn't work then im stumped and hopefully some seasoned vet can figure this out.
|
Re: Please Help :)
after i said no to the file transfers it does complete the Hard-SPL-MFG prog. and goes through and it fails.
|
Re: Please Help :)
Mail the phone to me and I'll fix it. Then it'll all be over. Lol.
|
Re: Please Help :)
don't run the Hard-SPL-MFG program. Run the sprint rom (any OS/Radio rom will do) and then go through the steps and RUU should pop up with an error. Then click next and follow the steps to try and do the repair.
|
Re: Please Help :)
You have to do what phonejunkie said. You'll want to find a Titan ROM that is compatible with your SPL-1.20.Olipro bootloader and install that. Hopefully it will also be compatible with the radio that you have.
Then, upgrade to the bootloader/SPL that the custom ROM that you want to flash requires. That new bootloader or ROM may require a new radio be installed. Then install your custom ROM. Good luck! |
All times are GMT -4. The time now is 09:40 AM. |
Powered by vBulletin® ©2000 - 2024, Jelsoft Enterprises Ltd.
©2012 - PPCGeeks.com