Diamond data issues - RESOLVED ! Woo Hoo !!
 

Hi Guys,

I've been wracking my brain over this one for days with little progress. I've searched the forums high and wide as well as the Internet as a whole without success. I've called Telus Tech support numerous times trying to resolve the issue to no avail.... This post is somewhat of a last resort so here goes...

I bought a used Telus Diamond from a fella in Calgary about a month ago and only activated it on the Telus Network a week and a half ago as a replacement for my Vogue. I love the phone and have been busy trying custom ROMs, etc and getting it just the way that I want it.

The issue lies with the data connection. Basically the phone stays in 1X after a voice call and won't come out of it till a soft reset. Initially, the phone shows Ev in the top bar but as soon as I use it to make a voice call, it reverts to 1X (as it should) but won't switch back to Ev after the voice call has finished. Also, if I use the data connection in Ev after soft resetting it, it behaves like my Vogue did before it's REV A update and won't ring if there's an incoming voice call.

Honestly guys, I'm pulling my hair out over this. Is there any way to completely refresh the phone back to the factory state (i.e., deeper than a hard reset) and start from square one again? Telus support are of the opinion that it's a hardware issue but I suspect it's because they want me to shell out more $$$ for a replacement (it's out of warranty by 2 weeks!). I know that you guys are way smarter than me (and Telus tech support incidently) and am hoping that you may have some things for me to try prior to my throwing in the towel.

Cheers and thanks in advance!

Nathan

Re: Diamond data issues - please help !
 

I would reflash to stock... then reflash the radio... then flash to stock again... and see if that helps

Re: Diamond data issues - please help !
 

Hi p2k,

Thank you very much for the reply. I've flashed back to the stock ROM, and tried a couple of radios (Sprint & Telus) with no success. However, I will do exactly as you suggested and report back.

Cheers,

Nathan

Re: Diamond data issues - please help !
 

Oh if you've already tried that... have you tried pulling the battery?

Re: Diamond data issues - please help !
 

hmm, it sounds to me like more of a software issue, but it could be because of a bad radio, I don't know. Has it always done this, or was it after a specific ROM? maybe if it started after flashing a WM6.5 ROM you could try clearing the internal storage as well. I read 6.5 roms can leave pieces of itself in the internal storage, so that could be why flashing other ROMs wasn't helping. It could also be a coverage issue, but i'm assuming your Vogue had no issues.you could also try updating your PRL, or some of the other technical stuff that I don't know, but other geekers should be able to help you with.

Re: Diamond data issues - please help !
 

Go to ##778# and put your MSL in then go to HDR and make sure the default is Hybrid in there.

Re: Diamond data issues - please help !
 

Hi p2k,

Ok, tried exactly as you suggested. No joy yet but thanks for the advice. As for pulling the battery, I've given that a go multiple times with tech support....

Re: Diamond data issues - please help !
 

Hi Snowplow, thank you for your suggestion. I was a little naive when I first got the phone and started flashing before registering it on the Telus network. Having said that, I did heed the advice of others and 'always' flashed back to stock before trying a different ROM. At any rate, I had Al's 6.1 ROM installed when I registered the handset on the network and hadn't tried any others since. I did try a 6.5 ROM for a short period before Al's ROM but quickly flashed back to stock then Al's ROM (6.5 just wasn't for me - yet). I've hard reset multiple times and wiped the internal storage clean. Updating the PRL had no effect. EVDO coverage certainly isn't the issue either. Good solid EVDO area.

Re: Diamond data issues - please help !
 

Hi MrObvious and thank you very much for the reply. At your suggestion, I logged into EPST and under 'Modem Settings', I noticed that 'HDR Hybrid Preferred' was 'Disabled'. I changed the state to 'Enabled', reset but unfortunately am still in the starting gate (still have the problem). Your idea gave me one though. I fired up my Vogue and put them side by side with EPST running on both to see whether they were somewhat similar.

The only other thing (Beside the HDR Hybrid Preferred being enabled on the Vogue) different between the two was under 'NAM Settings-NAM01' where on the Vogue, the value next to ACCOLC was 1 and on the Diamond it was 7.

Re: Diamond data issues - please help !
 

Did you try a hard reset after changing the Modem setting?? Then check if your change sticked...